Kenmore Refrigerator 106.9550750 (1069550750, 106 9550750) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2323197
This defrost heater warms the evaporator during automatic defrost to melt built-up frost so air can move freely and temperatures stay consistent. Replace a failed heater to restore normal cooling and end recurring frost on the freezer panel.
- Melts ice from the evaporator coil during the defrost cycle
- Prevents frost buildup that restricts airflow and causes warm spots
- Helps maintain stable refrigerator and freezer temperatures
- Typical failure signs: heavy frost on the back wall, reduced cooling, fan noise from ice contact, frequent manual defrosting
Includes: 1 defrost heater
- Disconnect power before servicing; wear cut-resistant gloves
- Access through the freezer compartment; remove shelves/ice bin and rear panel to reach the evaporator
- Match wire connections and route leads exactly as original; keep wiring clear of the fan and sharp edges
- After reassembly, restore power and monitor a defrost cycle; if frost quickly returns, also evaluate the defrost thermostat and control
Do-It-Yourself Stories from Customers like You
Circuit breaker would reset once refrigerator goes into defrost mode John C. • Elk Grove , CA • November 16, 2016
Replaced defrost heater with the help of the appliance parts pro how to video.
Video had made doing the job with ease. Had a laptop next to me making sure I had not missed a step. Been a week and things been all good. Well worth it. Thank you!
Read more
More
$61.75
- Compare At:
-
$74.10
- You Save:
-
$12.35
Genuine Whirlpool part
By: Whirlpool
Part Number: WP627018
Size: 1/4 inch. Nut for plastic water line.
Do-It-Yourself Stories from Customers like You
Broken y connector off of water valve on amana refridgerator Greg S. • El Dorado Hills , CA • October 19, 2014
Ordered part from AppliancePartsPros.com and received it 2 days later. Put the part in, fit like a glove, water and ice cube maker working flawlessly again with no leaks. Thanks.
Read more
More
$11.95
- Compare At:
-
$14.34
- You Save:
-
$2.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2155013
Clip for bottom grill. If your original clip is riveted, order screw WP489478.
Do-It-Yourself Stories from Customers like You
Age and misuse took its toll on the appliance parts ordered and received almost the next day Michael L. • Longmont , CO • February 21, 2015
Easy fixes, but I did what one of your video clips
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: 2188404A
The Refrigerator Door Gasket is an OEM part for Whirlpool refrigerators. This gasket forms a seal around the refrigerator door, ensuring that cold air stays inside and warm air remains outside, maintaining the appliance's efficiency and keeping food fresh.
Causes of a bad door gasket can include regular wear and tear, mold or mildew buildup, and physical damage from repeated opening and closing of the door.
Symptoms of a bad refrigerator door gasket include:
- Warm air entering the refrigerator, causing it to run more frequently
- Condensation or frost buildup inside the refrigerator
- Difficulty keeping the door closed
- Visible cracks, tears, or deformation in the gasket
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Condensation was forming along the top interior of refrigerator Susan H. • Springfield , NJ • September 10, 2014
I called Appliance Parts Pros and gave them the model number of my refrigerator. They promptly advised me exactly what part I needed, told me the price and cost of shipping. I agreed and received my part within 2 days.
I watched the video that told me exactly how to complete repair. It was very simple. The only thing different was that there was a metal strip holding the gasket in place. Removing it was no problem. When I installed it I had to loosen the screws? nuts? slip the gasket...
Read more
More
$135.43
- Compare At:
-
$162.52
- You Save:
-
$27.09
Genuine Whirlpool part
By: Whirlpool
Part Number: WP4387911
This push-button door switch senses when your refrigerator door opens and closes to control the interior light. Replace a worn or stuck switch to restore reliable lighting and proper on/off operation when the door moves. What it does:
- Turns the interior light on when the door opens and off when it closes
- Common fix for a light that won't turn on with the door open
- Resolves lights that stay on continuously with the door closed
- Addresses intermittent lighting from a sticking or damaged plunger
What's included:
Install notes:
- Disconnect power to the refrigerator before servicing
- Carefully pry the old switch from the liner; protect the surface to avoid damage
- Transfer wires to the new switch one at a time to maintain correct connections
- Press the new switch fully into place and restore power to test operation
Do-It-Yourself Stories from Customers like You
A failed freezer door switch was causing the fridge to display that the door was open when it was not this caused it to beep at random Kara H. • Charleston , SC • March 08, 2016
We actually were able to determine that one of the freezer switches was bad and taped it down for about 3 days. The beeping stopped. Our fridge has two freezer switches and one fridge side switch. I ordered all three from these guys. They were cheaper than Whirlpool by about $20 for parts and about $15 for shipping. The part numbers had superseded too many times to count, usually that doesn't matter but in this case it did. The new parts were just slightly bigger than the old parts AND...
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Whirlpool part
By: Whirlpool
Part Number: 72032
Bottle with brush. Color: Black. Size: 0.6 fl.oz.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$17.76
- Compare At:
-
$21.13
- You Save:
-
$3.37
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2179234
This meat pan trim is the front handle piece for your refrigerator's deli/meat drawer. It restores a secure grip and clean, finished look so the drawer opens smoothly and stays attached to the pan.
- Attaches to the front edge of the meat/deli pan and serves as the drawer handle and trim
- Helps keep the pan properly seated for smooth in-and-out operation
- Replaces cracked, broken, loose, or missing trim/handle
- Can resolve issues like a hard-to-open drawer or a pan that won't stay in place
What's included: One meat pan trim/handle Install notes:
- Disconnect power; remove the meat pan and place it on a protected surface
- Remove the damaged trim and clean the pan's mating surfaces
- Align the new trim with the pan lip; press or slide it on until fully seated
- Reinstall the drawer and verify smooth operation before restoring power
Do-It-Yourself Stories from Customers like You
Broken snack tray shelf and cracked snack pan and meat pan. Heather D. • Valley Park , MO • February 19, 2021
Just removed the broken items and replaced new ones all in under five minutes.
Read more
More
$47.95
- Compare At:
-
$56.58
- You Save:
-
$8.63
Genuine Whirlpool part
By: Whirlpool
Part Number: W10136387A
Color: clear. It measures about 6 inches wide by 3-1/2 inches high by 15 inches deep.
Do-It-Yourself Stories from Customers like You
Missing egg case for frig Laura W. • Coupeville , WA • June 19, 2016
I got online and found the egg carton case for my refrigerator - ordered it - it arrived and was exactly what I wanted. Online shopping is AMAZING!!
Read more
More
$11.34
- Compare At:
-
$13.49
- You Save:
-
$2.15
Genuine Whirlpool part
By: Whirlpool
Part Number: 4388539
Shelf stud
Do-It-Yourself Stories from Customers like You
Broken refrig shelf John T. • San Diego , CA • June 18, 2019
Watched video on your website - it was very helpful.
Read more
More
$18.44
- Compare At:
-
$21.76
- You Save:
-
$3.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP1106508
This gasket/seal creates a tight barrier between two mating parts in your appliance to prevent leaks and performance loss. Replacing a worn gasket restores proper sealing and helps stop seepage at the joint. What it does
- Forms a reliable seal between components to prevent fluid or air leaks
- Maintains proper operation by keeping the sealed area contained
- Replaces gaskets that are brittle, cracked, flattened, or swollen
- Common signs include residue or moisture around the joint, visible wear on the old gasket, or a loose/poor seal
What's included
Install notes
- Disconnect power and any water or gas supply before servicing
- Note the gasket's orientation; compare old and new parts before installation
- Clean and dry mating surfaces; remove old adhesive and debris
- Seat the gasket evenly; do not overtighten fasteners; test for leaks after reassembly
Do-It-Yourself Stories from Customers like You
Delivery person broke fitting off for the ice maker while removeing our "good" old fridge that was already sold Donald J. • Fremont , MI • October 13, 2014
I ordered the repair parts that Lowes said they couldn't get. I got the parts very fast and only took 5 minutes to get the job done.
Read more
More
$6.42
- Compare At:
-
$7.58
- You Save:
-
$1.16
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP2196090
This is the ice container that stores and dispenses ice from the freezer. A clear, intact bin helps ensure reliable ice storage and smooth dispensing without jams or spills.
- Holds and presents ice to the auger/crusher for dispensing
- Replacing a cracked or warped bin helps prevent ice jams and leaks
- Common symptoms: broken/cracked bin, ice spilling, poor/irregular dispensing, bin not seating properly
What's included: One ice container (bin/bucket) as a complete assembly as supplied by the manufacturer. Install notes:
- Unplug refrigerator and remove the ice maker bin before service
- Depress release latch (if equipped) and lift bin straight out
- Transfer and seat the new bin fully so it locks into place
- Restore power and test ice dispensing for smooth operation
Do-It-Yourself Stories from Customers like You
Ice containter was cracked Kristy L. • Plaquemine , LA • July 06, 2015
Replaced with new container
Read more
More
$87.46
- Compare At:
-
$103.78
- You Save:
-
$16.32
Genuine Whirlpool part
By: Whirlpool
Part Number: 4387491
These inserts are for 1/4 inch plastic tubing. Package of 4.
More
$11.95
- Compare At:
-
$13.22
- You Save:
-
$1.27
Genuine Whirlpool part
By: Whirlpool
Part Number: 4387535
This compressor overload is the thermal protector for your refrigerator's compressor. It opens the circuit when the motor overheats or draws excessive current, helping prevent damage and restoring reliable starts when the original protector fails.
- Interrupts power to protect the compressor during overheat or overcurrent conditions
- If failed, symptoms include: compressor won't start, repeated clicking or brief hum then stop, warm refrigerator/freezer, and an unusually hot compressor shell
- A weak protector may trip repeatedly and reset after cooling, causing intermittent cooling
- Works in tandem with the start relay/device to manage compressor startup current
What's included: 1 compressor overload protector Install notes:
- Disconnect power before servicing and pull the unit forward for rear access
- Remove the rear cover; note wire positions and take a photo for reference
- Pull the old overload straight off the compressor terminal; transfer leads and firmly seat the new overload in the same orientation
- Capacitors can retain a charge—handle with care; reinstall cover and restore power to test
This part fixes the following symptoms
-
Won't start
-
Fridge too warm
See more...
Do-It-Yourself Stories from Customers like You
Overload switch stopped working turning off the refrigerator compressor J Michael L. • Waxahachie , TX • August 06, 2016
Replaced overload switch and start relay with convenient repair set.Video available on website that gave step by step instructions. Followed the video steps for removal and installation.... plugged in the refrigerator compressor started up everything cool in minutes
Read more
More
$84.45
- Compare At:
-
$100.50
- You Save:
-
$16.05
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400906
This replacement screw secures appliance panels and internal components. Installing a correct OEM fastener restores a tight fit, reduces rattles and vibration, and helps keep assemblies aligned so your machine operates smoothly.
- Fastens brackets, panels, ducts, or housings to the cabinet or frame
- Replaces missing, stripped, or corroded hardware
- Helps stop rattles, vibration, and loose or misaligned parts
- Maintains proper alignment for reliable operation
Includes: 1 screw
- Disconnect power; shut off gas and water before servicing
- Match this screw to the original location and hardware type used on your model
- Start threads by hand to avoid cross-threading; use the correct driver
- Snug only—do not overtighten, especially into plastic or thin sheet metal
Do-It-Yourself Stories from Customers like You
Broken ice maker door and tabs David G. • San Antonio , TX • December 22, 2018
Through your website and YouTube DIY’s I was able to find the parts for my specific refrigerator and fix it, the wife had been after me for over a year to fix it and did not. I was ready to buy a new refrigerator but decided to try and fix it myself you guys rock !
Read more
More