Kenmore Washer 110.15954401 (11015954401, 110 15954401) Parts

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This replacement sleeve fits over a rotating shaft to reduce friction and protect the mating surface, helping restore smooth operation and reduce noise. Use when a worn sleeve causes rubbing or uneven movement. What it does:

• Acts as a bushing to prevent metal-to-metal contact on a rotating shaft
• Reduces friction and wear on the shaft and surrounding components
• Helps stop rubbing, scraping, or squeaking noises caused by a worn sleeve
• Restores proper alignment for smoother, quieter operation

• Disconnect power (and gas, if applicable) before starting any repair
• Use basic hand tools; no special training required for most installations
• Inspect the shaft and mating surfaces; replace if excessively scored or damaged
• If press-fit, install carefully to avoid damaging the new sleeve; do not use solvents as a substitute for proper fit

This E ring is a small metal retaining clip that secures shafts, pulleys, and other rotating parts to prevent axial movement. It restores correct part positioning so assemblies run smoothly and stay aligned. What it does:

• Acts as a snap/retaining ring to hold components on a shaft or in a groove
• Prevents pulleys, bearings, or spacers from sliding out of place
• Common symptom: loose or shifting pulley, increased wobble, noise, or component disengagement
• Small, inexpensive part whose failure can allow adjacent parts to migrate and cause additional damage

• Disconnect power to the appliance before beginning any repair
• Use snap-ring pliers or needle-nose pliers and wear eye protection when installing or removing
• Ensure clip seats fully in the shaft groove and that mating surfaces are clean and undamaged
• Replace any damaged mating hardware rather than reusing a deformed clip

For end of drain hose.

This hose coupling connects a flexible appliance hose to the appliance plumbing, restoring a secure water connection and preventing leaks. Ideal when a worn or damaged coupling causes drips or loose hose fit. What it does:

• Provides a secure connection point between an appliance hose and the appliance inlet
• Replaces cracked, broken or corroded couplings that can leak or allow the hose to detach
• Restores proper hose sealing to reduce water drips at the connection
• Compatible with the original inlet connection type and mounting orientation

• Turn off and disconnect appliance power and shut off the water supply before replacing
• Remove the old coupling and clean the mating surfaces; inspect hose and clamps for wear
• Use proper clamps and hand-tighten; avoid over-tightening which can damage fittings

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This auger agitator moves ice through the refrigerator dispenser so cubes and crushed ice flow smoothly to the user. It replaces a worn or damaged auger to restore normal dispensing performance. What it does:

• Rotates inside the dispenser chute to push ice toward the dispenser outlet
• Helps prevent ice clumping and improves consistent dispensing
• Commonly replaced when ice won't dispense, dispenses slowly, or makes grinding noises
• Compatible with models that use a motor-driven auger assembly

• Disconnect power to the refrigerator before starting any repairs
• Remove the dispenser cover and ice bucket per your model's service instructions to access the auger
• Inspect for ice jams or broken plastic fragments before installing the new auger

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

This drain hose coupling kit connects the washer drain hose to the appliance drain outlet, restoring a secure, leak-resistant hose connection and preventing water leaks during drain cycles. What it does:

• Provides a replacement coupling to join the drain hose to the washer drain outlet
• Re-establishes a tight hose connection to reduce leaks and water damage
• Addresses symptoms such as leaking at the drain connection or a loose hose fit
• Compatible with affected Whirlpool top-load washer drain assemblies

• Unplug the appliance before servicing and work on a dry surface
• Remove the old coupling and inspect the hose and outlet for damage before installing
• Ensure the hose is fully seated and secure with the existing or supplied clamp(s)

This rotary cycle selector switch lets the user choose wash or dry cycles so the appliance follows the selected program. It replaces a worn or unresponsive selector to restore proper cycle selection and control. What it does:

• Selects the appliance cycle when the knob is turned so the machine runs the chosen program
• Re-establishes electrical connection between the control and the timer/control board
• Commonly replaces switches when the knob turns freely but the cycle won't change
• Helps resolve intermittent or no-response cycle-selection issues

• Disconnect power before servicing to avoid shock or injury
• Remove the control panel or console to access the switch
• Note knob orientation or take a photo before removal to ensure correct reassembly
• Handle electrical connections carefully and test the appliance after reassembly

Color: White

This motor shield covers the drive motor on top-load washers to deflect splashes, lint, and debris away from the motor and wiring. Replace a cracked or missing shield to help protect the motor assembly at the base of the machine. What it does:

• Covers the washer's drive motor to deflect incidental water and debris
• Helps protect motor windings and terminals from splashes
• Replaces a cracked, warped, or missing cover
• Common signs: visible damage, rattling from the base, or corrosion/debris buildup around the motor

• 1 motor shield

• Unplug the appliance and turn off water supply before servicing
• Access the motor area from the bottom of the cabinet; note the shield's orientation
• Remove the damaged shield and install the new shield fully seated, reusing existing fasteners/clips
• Confirm clearance from moving parts before restoring power and testing

A cam sleeve that supports and guides the cam on its shaft to keep the cam-driven mechanism moving smoothly. Replacing a worn sleeve helps restore correct alignment and reduces binding or intermittent movement. What it does

• Centers and stabilizes the cam on its shaft for reliable engagement.
• Prevents metal-on-metal wear between the cam and shaft.
• Helps eliminate binding, wobble, or uneven operation caused by a worn sleeve.
• Common symptom of failure: noise, sticking, or irregular movement from the cam-driven mechanism.

• Disconnect power to the appliance before beginning any repair.
• Access typically requires removing the appropriate service panel; follow the model service manual.
• Inspect mating cam and shaft for wear; replace any damaged components.
• Reassemble panels and verify proper operation before returning the appliance to service.

This spring-damper assembly cushions and stabilizes moving components to reduce noise, vibration and abrupt motions. It restores smoother operation and helps prevent wear on related parts. What it does:

• Absorbs shock and controls motion to reduce banging or sudden movement
• Stabilizes moving components for quieter, smoother operation
• Helps prevent accelerated wear on hinges, levers or linkages
• Addresses symptoms like excessive vibration, rattling or irregular movement

• Disconnect power (and water if applicable) before starting any repair
• Handle carefully; springs can be under tension—wear safety glasses and gloves
• Basic hand tools typically required; follow OEM service instructions for alignment
• Inspect and replace other suspension or hinge parts as needed for best results