Kenmore Washer 110.15954401 (11015954401, 110 15954401) Parts

Right hand side. For screws use WPW10119828.

Used from harness to top.

This small mounting screw secures the appliance's timer to its bracket or control console. It replaces missing or stripped hardware to keep the timer stable, properly aligned, and operating smoothly when you turn the control knob.

• Fastens the timer assembly securely to its mounting bracket or console
• Prevents shifting and vibration that can make the control feel loose or wobbly
• Helps maintain proper alignment of the timer shaft/knob
• Ideal replacement when original hardware is missing or threads are damaged

• Disconnect power before servicing; shut off gas if applicable
• Access the control console and support the timer while removing/reinstalling hardware
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening into plastic or thin metal
• Replace screws one at a time to keep the timer aligned

This replacement control knob restores a secure, accurate way to select settings on your appliance. Installing this part brings back confident control and a clean, factory look.

• Mounts to the control shaft so you can turn and select settings
• Replaces worn, cracked, or missing knobs to restore normal operation
• Helps resolve symptoms like wobbling, spinning freely, or difficulty turning
• Restores proper pointer alignment and tactile feel when adjusting settings

• Disconnect power before servicing; for gas appliances, also shut off the gas supply
• Pull the old knob straight off the shaft; no tools needed in most cases
• Align the new knob with the control shaft and press firmly until fully seated
• Inspect the control shaft for damage; if bent or stripped, additional parts may be required

Size: .20 Fl. Oz. (6 ml)

Straight knurled pin that secures knobs or small components to a shaft for a tight, slip-resistant fit. Replaces a worn or missing pin to stop loose, wobbly, or spinning knobs and restore reliable engagement. What it does:

• Secures knobs, dials or small parts to control shafts by providing a press-fit, knurled surface.
• Prevents wobble, slipping, or spinning of control knobs that won't turn with the shaft.
• Common service symptom: knob spins freely or fails to engage controls.
• Used where a small metal pin is required to lock a component onto a splined or smooth shaft.

• Disconnect power and unplug the appliance before servicing.
• Remove the knob or access panel to reach the shaft; pin is typically press-fit.
• Removal/installation may require needle-nose pliers, a small punch, or a bench press; protect surrounding parts from damage.
• Keep small parts away from children and follow appliance safety guidelines; replace mating hardware if the shaft or hole is damaged.

Includes suspension pads.

This clutch spring cap retains and protects the clutch spring in your washer's drive/clutch assembly, maintaining proper tension. Replacing a worn or missing cap helps the clutch engage smoothly and reduces slipping and noise during spin.

• Secures the clutch spring within the clutch assembly to prevent movement or dislodging
• Maintains correct spring preload for consistent clutch engagement
• Can help reduce clutch slip that appears as weak/no spin, slow spin ramp-up, or intermittent spinning
• Common signs of trouble: rattling or scraping near the drive, burning smell, or a visibly damaged/missing cap

• Unplug the appliance and shut off water before servicing
• Access the clutch per your model's service procedure; removing the gearcase/transmission and clutch may be required
• Carefully relieve spring tension and note the orientation of the spring and cap before removal
• Inspect the spring, clutch lining, and related hardware; replace any worn components during reassembly

A replacement thrust bearing that supports the washer transmission shaft to reduce axial wear and help the gearbox rotate more smoothly. Use this bearing to address noisy transmission operation and reduce metal-on-metal wear when the original is worn. What it does:

• Supports axial load on the transmission/gearcase shaft to reduce friction and wear
• Helps prevent grinding, scraping, or other metal-on-metal noises from the gearbox
• Can reduce rough or noisy spin and improve agitation when a worn bearing is the cause
• Helps maintain proper alignment of transmission components for smoother operation

• Disconnect power and water supply and drain the washer before beginning any work.
• Replacement requires accessing the agitator/gearcase per the OEM service manual and may involve transmission/gearcase disassembly.
• Inspect nearby seals, fasteners and other bearings while servicing; replace damaged parts to avoid premature failure.

Color: Gray. Size: 13 oz. can. Used for coating the dryer drum interior. Acrylic appliance paint.

Size: 10-24 x 3/8 inch.

This drain hose clamp secures the hose connection to keep water where it belongs during the drain cycle. A tight, reliable clamp helps prevent leaks and hose pull-off from vibration or pressure changes. What it does:

• Secures the drain hose to a pump outlet or drain port to maintain a watertight seal
• Helps prevent the hose from slipping off during operation
• Reduces leaks at the hose connection point
• Common symptoms of a bad clamp: water leaking at the drain hose joint, a loose/detached hose, or a visibly rusted/broken clamp

• 1 clamp

• Disconnect power and turn off the water supply; place a towel to catch residual water
• Access the hose connection, remove the old clamp, and inspect the hose end and fitting; replace the hose if cracked or swollen
• Position the new clamp correctly over the hose and behind the fitting bead; tighten/seat evenly without overtightening
• Reassemble and run a brief drain test to check for leaks

This drain hose coupling connects two sections of the washer drain hose to restore a watertight path for wastewater, helping prevent leaks and restore proper draining. What it does:

• Joins two drain hose sections or connects hose to a mating outlet for secure water flow
• Seals the hose connection to reduce leaks at the joint
• Restores proper draining when a damaged or missing coupling causes slow drain or leakage
• Designed to fit the OEM hose profile for a snug, stable connection

• One drain hose coupling as shown

• Turn off power and water supply before starting any repair
• Inspect hose ends for damage; trim to clean cut if required for proper fit
• Push hose ends fully onto the coupling and secure with manufacturer-recommended clamps

This thrust spacer positions and supports the washer tub assembly, keeping rotating parts aligned to reduce wear and maintain smooth operation. It's a small but important part for proper drivetrain alignment in top-load washers. What it does:

• Centers and spaces the tub or agitator relative to the gearbox/shaft to prevent metal-on-metal contact
• Helps maintain correct clearance for smooth spin and agitation
• Can reduce noise and vibration caused by misalignment
• Commonly replaced when wear or damage causes rubbing, grinding, or poor spinning performance

• One thrust spacer

• Designed for use with compatible washer assemblies; follow your model's service manual for fitment and orientation
• Disconnect power and water supply before servicing the washer
• Inspect adjacent seals, bearings, and shaft components while replacing the spacer; replace any worn parts

Color: Biscuit. Size: 13 oz. can. Enamel spray paint.

This oven timer is the control clock used to set and monitor cooking time and signal when baking or roasting cycles end. It restores timed cook functions and audible end-of-cycle alerts on compatible ranges. What it does:

• Controls and displays oven cook time and countdown functions
• Triggers the end-of-cycle tone when the set time completes
• Works with the oven's control circuitry to enable timed bake/roast operations
• Commonly replaced when timers fail to advance, don't keep time, or don't sound the end-of-cycle alert

• One oven timer assembly

• Disconnect power to the appliance before beginning any repair
• Access may require removing the control panel or back cover; handle trim and wiring carefully
• Transfer any knobs or mounting hardware from the old timer unless new hardware is provided