Kenmore Washer 110.28042701 (11028042701, 110 28042701) Parts

White bezel cover for washer dispenser. Snaps into place over soap, bleach, and softener compartments. Replace if cracked, broken, or discolored.

Top spring hinge for washer lids. Provides tension and pivot support for smooth opening and alignment. Replace if cracked, broken, or causing lid sag.

Connects drain hose sections to prevent leaks and restore proper wastewater drainage. Replace if coupling cracks or connection leaks during draining.

Powder-coated top panel that covers the cabinet opening and protects internal components. Replace if rusted, cracked, or damaged from bleach exposure.

Fix detergent not dispensing or leaking detergent with this washer dispenser assembly. Restores proper detergent flow during wash cycles.

Factory fastener that secures panels and components in your laundry center. Replace if missing, stripped, or corroded to maintain proper alignment.

This syphon breaker prevents dirty drain water from being siphoned back into the dishwasher, helping maintain proper draining and protect wash water from contamination. It's a direct-replacement drain air-break for compatible dishwashers. What it does:

• Stops backflow/siphoning from the household drain into the dishwasher
• Helps maintain proper drain performance and prevents wastewater re-entry
• Can reduce odors and cloudy or soiled dishes caused by contaminated wash water
• Works as part of the dishwasher's drain plumbing to preserve wash hygiene

• Disconnect power to the appliance and turn off water supply before servicing
• Replace only with identical part and ensure correct hose routing and secure clamps
• Inspect adjacent drain hoses and connections; replace damaged hoses or clamps as needed

This top panel lock replaces a worn or broken front lock that secures the appliance's top panel. It restores a solid, secure top panel and helps prevent accidental opening during use. What it does:

• Acts as the front latch to hold the top panel closed
• Prevents the top from shifting, rattling, or coming loose during operation
• Helps stop access to internal components when the top is closed
• Commonly used when the top panel is loose, won't stay closed, or the latch is broken

• Disconnect power before beginning any repair to avoid shock or injury
• Basic hand tools (screwdriver) are typically needed
• Remove the top panel carefully to access the lock; note screw locations for reassembly
• Test the lock and panel alignment after reinstalling to ensure proper operation

White control panel bezel for washers. Replaces cracked, broken, or discolored bezels on the front control area. Restores clean appearance.

If your washer makes loud grinding noises or won't spin properly, the stator plate may be worn. This stationary motor component supports smooth operation.

Fabric softener not dispensing or cup stays full of water? This washer dispenser assembly channels softener to the drum. Straightforward install.

Replace your washer's lower wire harness if dispensers or lower controls aren't working. Restores power and signal flow to bottom components.

This ground wire provides a safe chassis connection to restore proper grounding and reduce shock and electrical-fault risk. It replaces a frayed, corroded or missing ground lead to help keep the appliance electrically safe. What it does

• Connects the appliance chassis to the grounding system to prevent stray voltage on metal surfaces
• Restores a secure ground path if the original wire is broken, loose, or corroded
• Helps stop intermittent power faults or nuisance tripping caused by a compromised ground
• Addresses symptoms like visible wire damage, loose ground connection points, or grounding-related electrical issues

• One ground wire

• Always disconnect power (unplug or shut off the circuit breaker) before starting work
• Attach the ring/terminal ends to the designated chassis ground screw and the equipment ground point
• Route the wire away from moving parts, heating elements, and sharp edges; secure with existing clips or fasteners
• If terminal hardware is missing or damaged, replace with equivalent OEM-style fasteners and torque to specification

Washer outer tub assembly houses the inner basket and includes bearings and tub seal. Replace when cracked, damaged, or bearings are worn out.

Replacement 8-18 threaded screw for refrigerators and washers. Secures panels, brackets, and internal components. Needed when original is lost or damaged.

Suspension spring for washers. Supports the tub assembly during spin cycles. Replace if spring is stretched, broken, or detached from mount points.