Kenmore Washer 110.28837700 (11028837700, 110 28837700) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62750
The Whirlpool spacer is an OEM replacement part responsible for maintaining the proper spacing and alignment between the washer cabinet and the top panel. The spacer provides stability and support to the appliance. It ensures that the top panel is securely attached and evenly distributed, preventing any misalignment or instability during operation.
Causes of a bad spacer can include wear and tear over time, physical damage due to accidental impacts, or deformation from prolonged use under stress. These issues can lead to misalignment and operational inefficiencies in the appliance.
Symptoms of a bad spacer include:
- Misalignment of components
- Unusual noises during operation
- Difficulty in assembling or disassembling parts
- Reduced efficiency of the appliance
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Sold individually, four are needed to replace all parts. Screw part number WP3390631.
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3359452
This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.
Do-It-Yourself Stories from Customers like You
Whirlpool washer was shaking and moving in spin cycle Charles B. • Sioux Falls , SD • September 25, 2018
Replaced 2 springs and brackets. Also replace rear legs and front legs and re leveled. Works fine.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3390631
10 - 16 x 1/2
Do-It-Yourself Stories from Customers like You
Agitator wasnt sloshing Paige B. • Clarksville , TN • January 30, 2015
I looked inside and saw the teeth were worn off the "dogs" so I purchased the Cam Agitator repair kit and a new bolt. Getting the old bolt out was the hardest part since it was worn and rusted. I ended up having to buy a set of socket extensions and a set of stripped bolt sockets so $45 in tools and it took me an hour to get the old bolt out but putting everything back together was a breeze. I was very proud of myself, as a woman, that I fixed this problem myself and didnt have to pay a repair...
Read more
More
$7.31
- Compare At:
-
$8.70
- You Save:
-
$1.39
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62691
Rubber grommet for motor mount stud.
Do-It-Yourself Stories from Customers like You
Washer did not agitate Gary S. • Kimberling City , MO • December 26, 2016
Replaced dog ears.
Read more
More
$8.95
- Compare At:
-
$10.56
- You Save:
-
$1.61
Genuine Whirlpool part
By: Whirlpool
Part Number: WP62658
Washer thrust ring acts as a bearing spacer between the outer tub and basket drive, controlling end-play and reducing friction. Replace when worn to restore smooth, quiet operation and prevent premature wear.
Do-It-Yourself Stories from Customers like You
Washer driver block was worn out Melissa J. • Battle Creek , MI • March 15, 2015
Purchased parts from your site and did a self repair. Excellent quality , speedy delivery and easy to install. Now our 13 year old washer works as good as new.
Read more
More
$8.95
- Compare At:
-
$10.65
- You Save:
-
$1.70
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8529935
Washer won't agitate or spin? A failed drive motor prevents wash and spin cycles. DIY replacement restores proper operation in 1-2 hours.
Do-It-Yourself Stories from Customers like You
Noise during second spin cycle Brent B. • Indianapolis , IN • July 02, 2017
Started out as a replacement of the coupling between the motor and the basket transmission ( 2 of the 3 legs on the transmission side broken.. )... Bought a new pump, since I would have it off... or so I thought.. Metal output shaft into pump + years of moisture = pump rusted on. Put it all back together - runs fine... for a while.. Then the old pump bearings burn out. Back apart.. Cut the old pump off the motor. Reinstall everything... Nothing, Just sits there and buzzes... Now...
Read more
More
$253.95
- Compare At:
-
$302.20
- You Save:
-
$48.25
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8578209
Fixes poor cleaning or clothes not moving during wash cycle. This agitator restores proper wash action by rotating and lifting laundry through water. DIY-friendly repair.
Do-It-Yourself Stories from Customers like You
Agitator was broke Daniel P. • Madison , OH • August 09, 2016
Striped the agitator out and replaced the bottom portion of agitator.
What was amazing was I placed the order Friday at 5 pm. It arrived Saturday at7:30pm.
Read more
More
$100.95
- Compare At:
-
$121.14
- You Save:
-
$20.19
Genuine Whirlpool part
By: Whirlpool
Part Number: W10389328
Inner tub basket holds clothing during wash cycles. Replace if cracked, rusty, or broken. Installs in center of washer between outer tub and agitator.
Do-It-Yourself Stories from Customers like You
Replacement of rusty inner basket Michael K. • Paramus , NJ • April 18, 2015
Ordered the parts from AppliancePartsPros - super fast shipping, and even though I opted for regular shipping all of my parts arrived the very next day, including the big and bulky inner basket. Disassembly went smoothly, simply following the directions in the AppliancePartsPros video. The only problem I had was that the inner basket simply would NOT come of the drive block no matter what I did. Struggled for a few hours trying to take it off. Then, I called AppliancePartsPros and they said it...
Read more
More
$292.95
- Compare At:
-
$329.48
- You Save:
-
$36.53
Genuine Whirlpool part
By: Whirlpool
Part Number: W10820044
Replacement power cord that connects your washer to the wall outlet. Includes strain relief for cable protection. Needed when original cord is damaged, pinched, shorted, or worn. Direct plug-in installation.
Do-It-Yourself Stories from Customers like You
Power cord got pinched and shorted out Gary D. • Kentwood , MI • July 27, 2014
Bought a new cord and removed the back of the washer and unclipped the old and clipped in the new. 5 minutes tops.
Read more
More
$78.95
- Compare At:
-
$93.95
- You Save:
-
$15.00
Genuine Whirlpool part
By: Whirlpool
Part Number: 285353
This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.
Do-It-Yourself Stories from Customers like You
Washer would agitate but would not go into high spin sounded like spin was working though Mario M. • Corona , CA • January 03, 2015
Im not a repairman, so all my knowledge to fix my washer came from either youtube or online chats. I posted this to help the next dad trying to save a few bucks.
Door sensor...
Since door sensor worked correctly, verified that by starting washer with door open, and agitate cycle would not start until door was closed. Meaning door sensor worked correctly.
Timer...
In high spin cycle washer sounded correcltly spinning, but when opening door, drum was was not moving. So timer was triggering...
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10086010
Secures the motor to its mounting point in your laundry center. Replace if the retainer is worn, broken, or has lost tension to prevent motor misalignment.
Do-It-Yourself Stories from Customers like You
The drive coupler was wore out upon fixing noticed clips were rusty and lost tension and start capacitor was badly corroded James H. • Waterloo , IA • February 03, 2017
Replaced with new retainer clips and new capacitor to fix future problems
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3400516
Secures panels or brackets in your laundry center to prevent vibration noise. Replace missing, stripped, or worn screws to restore a tight fit.
Do-It-Yourself Stories from Customers like You
Gearbox replacement Dennis M. • Comer , GA • October 21, 2018
Followed online video. It was easy
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8537434
This dishwasher cam assembly is a precision-molded drive component that converts rotation into the timed movement the mechanism needs. Replacing a worn cam helps restore smooth, reliable actuation during the cycle and reduces sticking or misalignment.
- Converts rotational input into precise motion for the linked latch/actuator mechanism
- Maintains proper timing and engagement so the mechanism operates when commanded
- Wear or cracking can lead to slipping, binding, or incomplete travel
- Typical symptoms: associated action fails to engage/release at the right time, intermittent operation, or clicking/grinding noises from the mechanism
What's included: 1 cam assembly Installation notes:
- Disconnect power at the breaker and shut off water before servicing
- Access the mechanism; note cam orientation and linkage positions
- Transfer any reusable pins/springs; install the new cam in the same orientation
- Run a test cycle to ensure proper operation and check for leaks or abnormal noises
Do-It-Yourself Stories from Customers like You
Agitator didn't work Rick K. • Naperville , IL • June 20, 2021
Simple by using 7/16 socket with long extension to remove the bolt and pull the whole agitator out and clean them. Put back in together with new parts. It works fine now.
Read more
More
$64.22
- Compare At:
-
$76.42
- You Save:
-
$12.20
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8578210
Agitator not working or spinning freely? This upper auger assembly restores the one-way ratcheting action for proper clothes rollover and cleaning.
Do-It-Yourself Stories from Customers like You
Agitator was not working Kenneth H. • Cleveland , TX • March 21, 2016
Ordered a agitator
Read more
More
$115.79
- Compare At:
-
$138.95
- You Save:
-
$23.16
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8533540
Fix agitator not working or washer won't spin. This spring retainer secures the tension spring in your agitator assembly. Easy 30-minute DIY repair.
Do-It-Yourself Stories from Customers like You
Agitator dogs worn & inner cap seal brittle. Natalie T. • Roosevelt , UT • August 05, 2017
Replaced dogs & cap seal. I also replaced Spring retainer since it was worn and I had it apart. Easy repair. Used a screwdriver to pop off fabric softener cap. socket to remove the agitator. I used a flathead screwdriver to remove the spring from the retainer. I cleaned everything and reassembled. It was a very easy repair. Saved at least $100. doing it myself.
Appliancepartspro.com is fast. I will buy from them in the future. Thanks guys!
Read more
More
Genuine Whirlpool part
By: Whirlpool
Part Number: WP389387
Agitator won't move or slips during wash? A worn drive shaft causes weak agitation. This shaft transfers motion from the gearcase to restore firm engagement.
Do-It-Yourself Stories from Customers like You
Agitator was not turning Edward M. • Glen Allen , VA • March 10, 2019
I had to replace the drive shaft and the lower agitator. The motor coupling was also worn out. The repair was challenging because I had to rebuild the gear box. This step was really messy and I had to wait for the liquid gasket to set prior to completing the repair. Cleaning and prep of all of the parts tripled the repair time.
Read more
More
$124.70
- Compare At:
-
$148.39
- You Save:
-
$23.69