Kenmore Washer 110.29832800 (11029832800, 110 29832800) Parts

Size: 10-24 x 3/8 inch.

Hearing grinding or wobbling during spin? This thrust spacer aligns the tub assembly in top-load washers. Simple install restores smooth operation.

5 foot. Package of 2.

Replacement shaft sleeve bushing for washers. Fits over rotating shafts to reduce friction and protect surfaces. Replace when worn, cracked, or missing.

Washer won't spin or vibrates excessively? This spring damper assembly cushions the drum during spin cycles, reducing vibration for smooth operation.

Secures your washer's drain U-bend to prevent leaks and keep plumbing properly aligned. Simple push-fit installation takes just minutes to complete.

This Smart ATC temperature switch senses and helps regulate oven temperature for more consistent cooking. It replaces a failed switch to restore correct temperature feedback to the range control for accurate heating. What it does:

• Detects oven temperature and sends a signal to the control so heating elements cycle appropriately
• Helps correct issues where the oven runs too hot, too cold, or cycles erratically
• Works as part of the temperature control system—does not include the main control board
• Replaces a worn or failed temperature/A.T.C. sensor switch to restore proper temperature sensing

• One temperature switch (Smart ATC)

• Disconnect power to the appliance before starting any repair to avoid shock or injury
• Access typically requires removing the oven control panel or back panel; keep track of screws and wire connections
• Handle the switch and connector gently to avoid damage; verify wiring matches original before reconnecting

A replacement selector knob selection assembly that restores a secure, easy-to-turn control for cycle or setting selection. Replaces a cracked, loose, or missing knob so you can confidently select functions again. What it does:

• Replaces a worn, broken, or missing selector knob used to choose cycles or settings
• Provides a secure grip and positive engagement with the control shaft
• Helps stop slipping, wobbling, or a knob that won't turn properly
• Restores normal control operation when the original knob is damaged

• One selector knob selection assembly

• Disconnect power to the appliance before starting any repair
• Most knobs pull straight off the control shaft; align the splines and press on until fully seated
• If the knob resists, verify orientation—do not force to avoid shaft damage

Secures shafts and pulleys in your washer to prevent axial movement. Replace when worn or damaged to restore proper alignment. Confirm fit with model.

Replace your washer's cracked or leaking drain hose. This flexible hose connects the tub to the drain system. Essential when the original is damaged or worn.

Secures panels and components in your washer to prevent rattles and maintain alignment. Replace when broken or missing to restore proper fit.

This 10-circuit connector housing provides a secure plug-style connection for the appliance wiring harness, restoring reliable electrical contact where the original plastic connector is cracked or melted. It helps ensure circuits stay seated and insulated. What it does:

• Replaces a damaged or cracked 10-circuit plastic connector housing to restore a proper plug connection
• Secures wiring harness terminals to prevent intermittent power or signal loss
• Keeps electrical contacts insulated from vibration and moisture
• Useful when the mating connector body is broken, burned, or otherwise unusable

• One 10-circuit connector housing

• Disconnect power to the appliance before starting any repairs
• Verify terminal pin type and wiring orientation before removing the old housing; take a photo for reference
• This listing is for the housing only; transfer existing terminals/pins or replace pins with exact matches as needed

This auger agitator moves ice through the refrigerator dispenser so cubes and crushed ice flow smoothly to the user. It replaces a worn or damaged auger to restore normal dispensing performance. What it does:

• Rotates inside the dispenser chute to push ice toward the dispenser outlet
• Helps prevent ice clumping and improves consistent dispensing
• Commonly replaced when ice won't dispense, dispenses slowly, or makes grinding noises
• Compatible with models that use a motor-driven auger assembly

• Disconnect power to the refrigerator before starting any repairs
• Remove the dispenser cover and ice bucket per your model's service instructions to access the auger
• Inspect for ice jams or broken plastic fragments before installing the new auger

This endcap assembly replaces a worn or damaged endcap to restore proper fit and protect the appliance's exposed end components. It helps keep parts aligned and prevents rubbing, vibration, and debris entry for smoother operation. What it does:

• Secures and protects the exposed end of the related component or housing
• Maintains proper alignment to reduce vibration, noise, and premature wear
• Replaces cracked, broken, or missing endcaps that allow movement or debris intrusion
• Restores finished appearance where the original endcap is damaged

• Disconnect power (and water if applicable) before starting any repair.
• Installation usually involves aligning the endcap and fastening or snapping it into place; confirm orientation before securing.
• Keep track of any screws or clips removed and reuse original fasteners unless replacements are specified.

The Switch Mounting Screw is an OEM part compatible with Whirlpool washing machines. This screw securely mounts the cycle selector switch within the control console assembly. Proper fastening ensures dependable operation of control functions.  

Causes of a bad mounting screw can stem from stress cracks developing over multiple years of operation. Vibrations accumulate, slowly loosening connections housed in a wet environment.

Symptoms of a bad mounting screw include:

• Loose or rattling switch within the console face  
• Difficulty selecting cycles as buttons wobble out of place
• Water intrusion hastening corrosion of electrical terminals
• Potential shock hazards if live connections are exposed

This Whirlpool replacement screw restores a tight mounting point. It is compatible with brands like Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.

Flat washer that spaces and aligns the agitator gear in your washer. Replace if worn, missing, or damaged to restore proper gear positioning.