Kenmore Washer 110.5905852 (1105905852, 110 5905852) Parts

Genuine Whirlpool part

Nut

By: Whirlpool

Part Number: 98460

$8.40

Compare At:: $9.98
You Save:: $1.58

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Genuine Whirlpool part

Hinge Pad

By: Whirlpool

Part Number: 18849

$13.61

Compare At:: $16.06
You Save:: $2.45

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Genuine Whirlpool part

Fill Hose

By: Whirlpool

Part Number: 76313

Size: 6 foot. This washer fill hose can be used for the hot or cold.

Genuine Whirlpool part

Washer Lid Switch Actuator

5.0 (2)

By: Whirlpool

Part Number: WP359807

The washer lid switch actuator is a small component that triggers the safety switch when the lid is closed. Located on the washer lid, it presses against the lid switch to signal that it's safe to operate. Replace if the washer won't start even with the lid closed, or if it continues running with the lid open.

This part fixes the following symptoms

Will not drain

Do-It-Yourself Stories from Customers like You The spin cycle on my washing machine was not working due to a faulty door/lid switch Joseph D. • Mechanicville , NY • February 17, 2015

I ordered a door/lid switch kit and an actuator and replaced them both. I probably didn't need the actuator, but it probably didn't hurt to replace it. The only issue I had was that the switch didn't seem to fit that well when installed on it's own, along with the actuator. So, I used the plastic shield which I had, along with the switch and actuator, as well as the old screws, as the screws that came with the kit were not long enough to accommodate the switch, actuator, and... Read more

Genuine Whirlpool part

Water Drain Pump

By: Whirlpool

Part Number: 350367

4 port. Whirlpool and Kenmore washers.

Genuine Whirlpool part

Tub Ring Clip

By: Whirlpool

Part Number: 359689

The tub ring clip is a small plastic or metal fastener that secures the tub ring to the outer tub of a washing machine, holding the two components together during the wash cycle. It prevents the tub ring from shifting or separating under the vibration of spinning and agitation. Replace it if you notice the tub ring is loose, rattling during cycles, or has come free from its mounting position.

Genuine Whirlpool part

Handle, Door C30" Blk

By: Whirlpool

Part Number: 487596

Genuine Whirlpool part

Outer Tub Repair Kit

By: Whirlpool

Part Number: 76673

Includes 4 rubber washers, 4 metal washers, and 4 screws.

Genuine Whirlpool part

Drive Block

By: Whirlpool

Part Number: 96384

Genuine Whirlpool part

Locator, Top

5.0 (1)

By: Whirlpool

Part Number: 98669

Do-It-Yourself Stories from Customers like You The door switch failed when the door was opened the machine still ran Peter B. • Davie , FL • July 10, 2016

Replaced the switch...your videos are great! Five minutes and the job was done..OK,maybe ten,but with no swearing either! Read more

Genuine Whirlpool part

Lid Hinge Bumper

5.0 (5)

By: Whirlpool

Part Number: WP19119

Do-It-Yourself Stories from Customers like You Washer was "dead" with a partially washed load and would not do anything Jimmy M. • Hopewell , VA • September 19, 2014

Researched this kenmore washer on-line and found the problem to be the lid switch. Saw a diagram on how to jump this switch by connecting a wire to both outside wires on the harness and voila! It worked! This is not a fix but it allowed me to finish the load of unwashed clothes and told me which part was bad (do not run washer jumped like this.......fire hazard!) Ordered the lid switch and it was an easy repair. A $14.00 switch was a lot cheaper than a $450.00 washer. Thanks appliance parts... Read more