Kenmore Dryer 110.87872603 (11087872603, 110 87872603) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP22002263
Illuminates the dryer drum for better visibility when loading and unloading. Replace when bulb burns out or fails to light. Confirm fit with your model.
Do-It-Yourself Stories from Customers like You
Squeaky noise and not fully drying David H. • Santa Clarita , CA • September 20, 2019
Originally the dryer was squeaking a lot, so I purchased a new belt tensioner, but the original tensioner was an old-style no wheel tensioner, so that wasn't the source of the squeaking.
I saw a lot of lint had built up inside the unit where there shouldn't have been that much. So I viewed a few videos on the Appliance Pros site and saw that the rear wheel guides were the cause of the squeaking and the rear felt drum and blower housing seal needed to be replaced. The rear blower housing was...
Read more
More
$15.55
- Compare At:
-
$18.50
- You Save:
-
$2.95
Genuine Whirlpool part
By: Whirlpool
Part Number: WP8557403
The Dryer Thermostat is an OEM part for Whirlpool dryers. It regulates the temperature inside the dryer, ensuring that it maintains the correct heat levels for safe and efficient drying cycles.
You should replace this dryer thermostat if it becomes faulty. Common causes of a bad dryer thermostat include electrical failures, buildup of lint or debris causing overheating, and general wear and tear over time.
Symptoms of a bad dryer thermostat include:
- Dryer overheating or not heating at all
- Extended drying times
- Dryer shutting off prematurely
- Error codes related to temperature control
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Took to long to dry John R. • Delphi , IN • January 02, 2015
After reading the reviews of others, I ordered and replaced the heating element, thermostat, cut-off & the moisture sensor bars. It was a success!
The element was definitely bad on one end, the wire was burnt in two pieces. Now it doesn't take 3 hours to dry a load! Well worth the money I spent. Easy to fix & do it yourself. I watched the video before buying the parts just to make sure that it was something I wanted to tackle. Very easy with the video. Great job Appliance Pro's!
Read more
More
$69.32
- Compare At:
-
$81.80
- You Save:
-
$12.48
Genuine Whirlpool part
By: Whirlpool
Part Number: WP697770
Seals the blower housing to prevent air leaks that reduce drying efficiency. Replace if worn, cracked, or missing to restore optimal airflow.
Do-It-Yourself Stories from Customers like You
Over heating. Robert B. • Hollywood , SC • October 14, 2017
Watched You tube videos to narrow the problem down to old deteriorated gaskets.
Read more
More
$9.41
- Compare At:
-
$11.20
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: 280148
The Thermal Cut Off is an OEM part for Whirlpool dryers. This safety device helps prevent the dryer from overheating by cutting off the power to the heating element if it detects excessively high temperatures. Ensuring proper functioning of the thermal cut off is crucial for the safety and efficiency of the dryer.
Causes of a bad thermal cut off can include regular wear and tear, exposure to high temperatures over extended periods, or electrical issues within the dryer.
Symptoms of a bad thermal cut off include:
- The dryer not heating up
- The dryer shutting off mid-cycle
- The dryer not starting at all
- Unusual overheating during operation
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
No heat Dan R. • Woodruff , SC • November 30, 2018
First ran the built-in diagnostic tests. Got error code indicating that the inlet thermistor was open. Removed lower access panel and did continuity checks on the inlet thermistor, thermal cutoff and heating element. Even doing these checks is very difficult on this model due to the location of these parts and the limited access through the so-called access panel. But was able to get an open reading on the heating element, so I knew that at least that part was faulty. Could not get a reliable...
Read more
More
$49.40
- Compare At:
-
$58.79
- You Save:
-
$9.39
Genuine Whirlpool part
By: Whirlpool
Part Number: 279787
Dryer won't start, makes grinding noise, or drum won't spin? The drive motor powers the drum and blower. Moderately difficult repair, about 1 hour.
Do-It-Yourself Stories from Customers like You
Motor would not start when start button pressed for one second lights up and hear motor solenoid click but no start Anthony Y. • Kaneohe , HI • October 11, 2014
Checked thermal fuse, belt pulley switch, door switch, and motor windings (primary 2.3 ohms start 2,2 ohms).
Called Appliance Pros, told them my problem. They said that it appears to be the motor even though the ohm readings seam Ok and that I could return the motor if it was not the problem.
I ordred the motor and blower wheel.
Installed the new motor and everything worked!
The only difficult part was that the motor blower had to be chiseled out.
Their motor repair video was a great help.
Read more
More
$163.95
- Compare At:
-
$193.46
- You Save:
-
$29.51
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10359272
The Drum Support Shaft for Left Hand Threads is an OEM replacement part for Whirlpool dryers. This component is essential for securing and supporting the drum as it rotates during the drying cycle. It helps maintain the drum’s alignment and stability, ensuring smooth and efficient operation of the dryer.
Over time, the drum support shaft can become worn out or damaged due to continuous use, the weight of laundry loads, or improper installation. Additionally, exposure to high temperatures and repeated mechanical stress can cause the shaft to weaken or fail, leading to issues with the dryer’s performance.
Symptoms of a bad drum support shaft include:
- The drum not rotating smoothly or making grinding noises
- Excessive wobbling or vibrating of the drum during the drying cycle
- The dryer taking longer to dry clothes or not drying them evenly
- Visible damage or wear on the shaft or its threads
- The drum becoming misaligned or not sitting properly within the dryer
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore models.
Do-It-Yourself Stories from Customers like You
Very loud and squeaky Michael M. • Chesapeake , VA • April 09, 2018
Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them.
Read more
More
$49.40
- Compare At:
-
$59.28
- You Save:
-
$9.88
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10446781
The Idler Arm Spring is an OEM part for Whirlpool dryers, maintains tension in the dryer's belt system. This spring is crucial for the proper operation of the dryer, as it helps to keep the belt tight around the drum and motor pulley, enabling the drum to rotate smoothly during cycles.
Causes of a bad Idler Arm Spring can include stretching or weakening over time due to constant tension, or breakage from wear and tear.
Symptoms of a bad Idler Arm Spring include:
- Unusual noises, such as squeaking or squealing
- The dryer drum may not rotate smoothly or may stop turning altogether
- Clothes take longer to dry, or you may notice uneven drying
- The dryer might not start if the belt is disengaged due to insufficient tension.
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
The drum belt or the tension pulley was maki a squealing noise when drying the clothes Harold W. • Albany , GA • July 06, 2015
Replace the drum drive belt and tension pulley assy.
Read more
More
$21.95
- Compare At:
-
$25.90
- You Save:
-
$3.95
Genuine Whirlpool part
By: Whirlpool
Part Number: W10837625
Motor pulley attaches to the dryer drum motor shaft and grips the belt to spin the drum. Replace if cracked, broken, or worn to restore proper operation.
Do-It-Yourself Stories from Customers like You
Motor pully broke and belt snaped Eric A. • Scottsdale , AZ • December 27, 2014
Replaced
Read more
More
$29.95
- Compare At:
-
$48.64
- You Save:
-
$18.69
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10359271
Shaft that secures front drum support rollers in your dryer. Replace if worn, scored, or damaged to restore proper drum alignment and support.
Do-It-Yourself Stories from Customers like You
Very loud and squeaky Michael M. • Chesapeake , VA • April 09, 2018
Replaced the Rollers, Pins, belt and belt tensioner. One thing to keep in mind. In the video it was said that the back and front roller pins were different by lengths. They were the same length for my model. The differences were found to be the rear pins have left handed threads and the front ones were standard right hand threads. Keep that in-mind when you are trying to remove them.
Read more
More
$49.40
- Compare At:
-
$58.79
- You Save:
-
$9.39
Genuine Whirlpool part
By: Whirlpool
Part Number: 49621
The Dryer Leveling Foot is an OEM part for Whirlpool dryers. It is designed to support and stabilize the dryer by allowing adjustments to the height and leveling of the unit. Proper leveling ensures the dryer operates smoothly and efficiently, reducing vibrations and preventing unwanted movement during cycles.
Causes of a bad leveling foot can include wear and tear from regular use, damage from moving the dryer, or breakage due to heavy loads and stress. Over time, the threads on the leveling foot can wear out, or the foot itself can become cracked or deformed.
Symptoms of a bad leveling foot include:
- Dryer rocking or wobbling during operation
- Unusual noises or vibrations
- Difficulty in adjusting the dryer's height
- Visible damage or wear on the leveling foot
This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Took the base off the washer and dryer and they had no feet on them. Paula S. • Onalaska , WA • March 22, 2014
Bought the leveling feet and screwed them in the bottom and they work great.
Read more
More
$6.95
- Compare At:
-
$8.27
- You Save:
-
$1.32
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3387230
Replacement mounting screw for securing handles, panels, and internal components. Needed when original screws are stripped, lost, or broken during repairs.
Do-It-Yourself Stories from Customers like You
The lint catch was broken Misti P. • Spokane , WA • January 18, 2019
This was actually one of the easiest fixes I’ve done. All that was required was to remove 3 screws to remove the broken part. I used a pair of pliers to remove the moisture sensors from the broken part to the new one.
Read more
More
$7.31
- Compare At:
-
$8.77
- You Save:
-
$1.46
Genuine Whirlpool part
By: Whirlpool
Part Number: 72017
Touch-up paint for covering scratches, chips, and minor blemishes on appliance exteriors. Restores appearance and protects surfaces when finish is damaged.
Do-It-Yourself Stories from Customers like You
Chipped paint Thomas S. • Middletown , DE • September 03, 2014
Touch up paint
Read more
More
$11.51
- Compare At:
-
$13.70
- You Save:
-
$2.19
Genuine Whirlpool part
By: Whirlpool
Part Number: 350930
Color: White. Size: 13 oz can. Acrylic appliance aerosol can spray paint.
The Appliance Spray Paint is an OEM part for Whirlpool appliances, designed to provide a quick and effective way to touch up or completely refinish the exterior of various appliances. This specialty spray paint is formulated to adhere to metal surfaces, offering a durable and resistant finish that can withstand the routine wear and tear of kitchen environments, including heat, moisture, and everyday use.
The primary reason for using such a specialized paint is to maintain or restore the aesthetic appeal of your appliances while protecting them from further damage.
Symptoms needing for Appliance Spray Paint include:
- Scratches, chips, or rust spots on the appliance's exterior that can lead to further damage or corrosion if left untreated
- A desire to refresh or update the appearance of the appliance without the need for complete replacement
- Discoloration or fading of the original finish due to age, exposure to sunlight, or cleaning agents
This OEM Whirlpool part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Leaking diaphragm Herbert S. • Monroe Township , NJ • January 03, 2015
Replaced It With New One
Read more
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99
Genuine Whirlpool part
By: Whirlpool
Part Number: WP697813
Seals the dryer outlet housing to prevent air leaks and maintain venting efficiency. Replace if lint accumulates in cabin or moisture escapes. Verify fit.
Do-It-Yourself Stories from Customers like You
Over heating. Robert B. • Hollywood , SC • October 14, 2017
Watched You tube videos to narrow the problem down to old deteriorated gaskets.
Read more
More
$9.41
- Compare At:
-
$11.20
- You Save:
-
$1.79
Genuine Whirlpool part
By: Whirlpool
Part Number: WPW10310366
Connects dryer door to cabinet, allowing smooth opening and closing. Replace if hinge is broken, worn, bent, or causing door misalignment issues.
Do-It-Yourself Stories from Customers like You
The hinge was wore out Terrance B. • Mattawan , MI • May 09, 2015
The part came within 3 days. The fix was straight forward ...unscrewed the hinge from the dryer then from the door and replaced with new hinge and the door closes the way it should.
Read more
More
$120.74
- Compare At:
-
$143.68
- You Save:
-
$22.94
Genuine Whirlpool part
By: Whirlpool
Part Number: W11129408
Houses and secures the lint filter in your dryer. Replace if cracked, warped, or broken to prevent lint bypass and maintain airflow. Verify fit by model.
Do-It-Yourself Stories from Customers like You
Dryer lint screen housing was warped. Michael D. • Reno , NV • January 29, 2022
Bought a new lint screen housing and top flapper. Probably didn’t need the flapper but I didn’t want to set into the repair and find out I did need it.
Read more
More
$47.34
- Compare At:
-
$56.81
- You Save:
-
$9.47