Kenmore Dryer 110.96563100 (11096563100, 110 96563100) Parts

Genuine Whirlpool part

Dryer Lint Chute

By: Whirlpool

Part Number: 279505

Lint chute directs lint and debris from the dryer drum to the lint screen. Replace if cracked, broken, or clogged to maintain proper airflow.

$151.64

Compare At:: $180.45
You Save:: $28.81

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Genuine Whirlpool part

Dryer Blower Housing Insulation Pad

5.0 (1)

By: Whirlpool

Part Number: 686889

Foam seal pad that cushions the dryer blower housing against the cabinet. Replace if cracked, compressed, or missing to restore proper fit and reduce vibration.

Do-It-Yourself Stories from Customers like You Thermal fuse had blown and wire had melted as a result Benjamin S. • Portland , ME • July 02, 2018

I replaced the thermal cutoff kit and a heating element connection wire. Super simple and probably saved me over $100 if I had called a repairman. The videos on your site as well as the customer service person I spoke with were SUPER helpful. Thank you!!! Read more

$23.61

Compare At:: $28.33
You Save:: $4.72

Out Of Stock

Usually ships within 4 - 14 days

Add to Cart

Genuine Whirlpool part

Dryer Door Hinge

5.0 (2)

By: Whirlpool

Part Number: WP238456

Right side

Do-It-Yourself Stories from Customers like You Our dryer had a broken latch and bad hinges Lawrence G. • St. Clair , MO • November 13, 2015

After watching a video on the Alliance Parts Pros website, I was able to easily fix the problem, quickly and easily. Read more

Genuine Whirlpool part

Guide Cable (Left)

By: Whirlpool

Part Number: WP337182

This left-side guide cable helps position and stabilize the appliance component it supports, restoring smooth movement and alignment for reliable operation. Designed to replace a worn or broken guide cable and reduce binding or misalignment. What it does:

Guides and supports the component assembly on the left side to maintain correct travel and alignment
Replaces damaged or frayed cable that can cause sticking, jerking, or uneven movement
Helps restore smooth operation and consistent performance of the guided assembly
Works as the matching left-side counterpart when paired with its right-side guide

What's included:

One left-side guide cable

Install notes:

Follow the appliance manufacturer's service instructions and disconnect power before beginning work
Handle cable ends and attachment points carefully to avoid fraying or damage during installation
Verify routing and attachment points match the original cable for correct operation

Genuine Whirlpool part

Guide Right

By: Whirlpool

Part Number: WP337183

Genuine Whirlpool part

Cable

By: Whirlpool

Part Number: 230131

Genuine Whirlpool part

Bulkhead

By: Whirlpool

Part Number: 279793

Genuine Whirlpool part

Endcap

By: Whirlpool

Part Number: 285508

Genuine Whirlpool part

Bracket, Support Shaft

By: Whirlpool

Part Number: 3976435

Genuine Whirlpool part

Box - Heater

By: Whirlpool

Part Number: 695547

This is the heater box only, does not include heating element.

Genuine Whirlpool part

Seal, Blower Shaft

4.8 (12)

By: Whirlpool

Part Number: WP3394196

Do-It-Yourself Stories from Customers like You The motor on our clothes dryer was doing a "self protection" thermal or overload shutdown and there was a strong odor in the tub Jim S. • Fallon , NV • November 27, 2015

It took two repair attempts to fix the dryer. At first, I noticed that the rear felt seal was completely worn out, so I thought that extra friction between the tub and the rear panel might be causing the motor to have to work too hard and overheat. I ordered a new seal from appliancepartspros.com, and installed it according to their instructional video, but it did not correct the problem. Then I decided that the motor must be going bad, so I watched the on-line video on how to remove the... Read more

Genuine Whirlpool part

Handle

5.0 (1)

By: Whirlpool

Part Number: WP3977746

Do-It-Yourself Stories from Customers like You The lever to turn on dryer was broken the handle was broken and the latch was broken David R. • Jemison , AL • February 09, 2015

I opened the top of the dryer (after watching the video on your website) and replaced the lever on the switch. Removed two screws near the lint filter, used a putty knife to release fasteners under the top and raised the top. Held it in place with a short piece of board then removed the two screws holding in the switch and lever. Replaced the broken lever with the new one and put it all back together. The handle was a little more difficult as it took a lot more prying with a screwdriver to... Read more