Kenmore Dryer 110.97573100 (11097573100, 110 97573100) Parts

Left hand hinge. For right hinge use WP8066056

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essen

The Dryer Door Handle is an OEM replacement part for Whirlpool dryers. A dryer door handle can deteriorate due to prolonged use, repeated force when opening or closing the door, or accidental impact that causes cracks or breakage. These factors may com

Includes two bumpers and two locking clips. You will use one or the other depending on hole size.

This flat support washer provides a stable bearing surface under a fastener. Its 1-1/2-in diameter helps distribute load, maintain spacing, and keep components aligned so hardware stays tight and assemblies operate smoothly. What it does:

• Distri
  Do-It-Yourself Stories from Customers like You Drum support bearing failure.   Myron D. • Covington , KY • July 13, 2018

  Simple fix, right parts fast. Read more

Size: 1/4 inch hex head, 10-12 x 1/2 inch.

Plastic drum baffle that lifts and tumbles clothes during drying. Replace if cracked, broken, detached, or missing from inside your dryer drum.

Factory protective shield panel for dryer assembly. Guards internal components and directs heat or airflow. Replace if cracked, broken, or missing.

Replace a cracked or missing bracket to keep appliance components securely mounted and aligned. Restoring this support helps prevent movement, vibration, and premature wear, so the connected part operates as intended.

• Provides a rigid mounting p
  Do-It-Yourself Stories from Customers like You Drive belt support rollers and idler pulley worn.   Carlos W. • Port Orchard , WA • May 30, 2020

  Disassembled dryer, replaced worn parts and reassembled dryer. Removed top cover, disconnected front connector, removed front panel, removed belt from idler pulley, removed washer drum and belt, replaced push clip, retaining clips, 2 support rollers and idler pulley. Reassembled in reverse order. Read more

This power cord connects your appliance to household electricity, supplying safe, reliable power to its controls and components. Replace a damaged or overheated cord to restore dependable operation and reduce the risk of shorts.

• Supplies AC powe
  Do-It-Yourself Stories from Customers like You New cord   Michael C. • Bakersfield , CA • May 10, 2021

  Thanks to you, all went well. No problems. Read more

Type AB #8-18 x 5/8 inch thread-forming screw secures panels and components in appliances. Replace missing, stripped, or corroded fasteners.

This replacement cover restores the appliance's finished appearance and protects internal components from dust and debris. It's a direct-fit exterior trim piece designed to replace a cracked, broken, or missing cover. What it does:

• Protects inte
  Do-It-Yourself Stories from Customers like You Broken coupling half   Neal F. • W Portsmouth , OH • February 27, 2026

  Replaced broken coupling with new coupling Read more

Supports and pivots the hinged dryer top panel for service access. Replace if cracked, broken, or causing wobble, scraping, or alignment gaps.

Replacement screw secures panels, brackets, and internal assemblies. Needed when original hardware is stripped, corroded, or missing to keep parts tight.

Short baffle that mounts inside the dryer drum to lift clothes as the drum rotates. Replace if cracked, broken, or missing for proper tumbling action.

This replacement ice chute directs ice from the bucket to the dispenser opening, helping prevent jams and stray cubes. If the original chute is cracked, warped, or obstructed, replacing it restores smooth, consistent ice dispensing. What it does:

Do-It-Yourself Stories from Customers like You Paint was spilled down lint chute screen was not removed quickly and became stuck in the chute   Jay C. • Albany , CA • November 26, 2016

I replaced the chute and screen - I am very mechanical and have good tools - it took me less than 30 minutes - would take many people longer but it is a straightforward project Read more