Kenmore Dryer 110.97580910 (11097580910, 110 97580910) Parts

Dryer won't heat or stops working? A burnt or melted terminal block disrupts power flow. DIY repair in under an hour with video guidance included.

Screw secures appliance panels and access covers. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattles or gaps.

The Terminal Block Kit is an OEM part for Whirlpool dryers. This kit includes the terminal block, wires, wire connectors, screws, brackets and instructions.

Common causes of a bad terminal block include overheating due to loose connections, cor

The Whirlpool screw is an OEM replacement part responsible for securing various components or parts on different types of Whirlpool appliances. The screw is designed to provide a secure and reliable fastening connection, ensuring that different parts o

Spring installs inside the gas pressure regulator assembly on gas dryers. Replace if lost during conversion between natural gas and propane fuel types.

Dryer making high-pitched sound when igniter turns on? This natural gas regulator maintains proper gas pressure to burners. DIY-friendly repair.

U-type clip nut slides onto sheet metal panels to create threaded anchor points for screws. Replace if broken, missing, or worn during repairs.

This support washer is a flat spacer used within the mechanism to support and separate mating parts, maintaining alignment and smoother movement. Replacing a worn washer helps reduce friction and wear so components operate properly. What it does:

Do-It-Yourself Stories from Customers like You Screaching noise   Linda Z. • Kailua Kona , HI • February 06, 2015

Followed the video- opened the front of the dryer and removed the drum. It was evident that one of the wheels had worn and wasn't turning freely like the other one. The video showed how to remove the roller. Very simple process and now the dryer works just fine. Read more

This console screw secures the control console to the appliance cabinet or top, keeping the panel tight and aligned. Replace a missing or damaged screw to stop panel wobble and rattling and maintain a snug, stable fit. What it does:

• Fastens the
  Do-It-Yourself Stories from Customers like You Leaking water from the tub seal   David C. • Bessemer City , NC • January 27, 2018

  THIE REPAIR WAS ON A WHIRLPOOL TOP LOAD WASHING MACHINE At first I suspected the leak was from the pump because I had replaced the pump 2 times over 10 years. This time with the cabinet removed and filling the tub with water, I saw water running down one of the steel support arms that go under the tub, so I was guessing that it was coming from the tub seal. I had to use a jumper wire to bypass the Lid Switch so the water would drain. Several months before I had this issue with the water leaking... Read more

If your dryer won't heat or flame won't stay lit, a corroded burner tube may be the cause. This assembly includes an adjustable air shutter for proper combustion.

This internal-bias thermostat regulates dryer drum temperature by cycling the heat on and off, helping maintain consistent drying performance and protect against overheating.

• Controls the cycling temperature of the heating circuit to prevent und
  This part fixes the following symptoms

  • Too hot

  See more...
  Do-It-Yourself Stories from Customers like You Thermal fuse blew   John P. • Palm Coast , FL • January 02, 2016

  Cleaned exhaust duct, but only from the dryer/laundry room side. Replaced thermal fuse. Unit worked for about two loads and thermal fuse blew again. This time I cleaned the exhaust vent on the roof of my 2-story house. It was found to be partially obstructed and I was able to remove a significant amount of lint from it. Also, I researched the problem and followed someone's advice to replace the cycling thermostat together with the thermal fuse if the thermal fuse blows. So far it has been... Read more

This 8-18 x 5/8-inch screw secures dryer panels, brackets, and covers. Replace missing or stripped fasteners to restore a tight fit and stability.

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes miss

The Door Hinge is an OEM part for Whirlpool dryers. This hinge ensures the secure attachment of the dryer door to the appliance, allowing it to open and close smoothly. Right-hand hinge. For the left hinge use Do-It-Yourself Stories from Customers like You Broken dry door hinge.   Lynda S. • Apex , NC • September 24, 2018

Watched your very helpful and informative "how to" video and replaced both right and left hinges. Getting the front panel to line up on the clips was the most difficult part. Read more