Kenmore Dryer 110.97586200 (11097586200, 110 97586200) Parts

Size: 6 - 20 x 1 1/16 inch.

This is the complete drum assembly for a clothes dryer - the large cylindrical tumbler where clothes are placed for drying. It rotates during the drying cycle to tumble clothes through heated air. Replace this assembly if the drum has cracks, holes, excessive wear marks, or if clothes are snagging or getting caught during operation.

Seals the rear of the dryer drum to prevent hot air loss and ensure even drying. Replace when worn, cracked, or causing noise. Verify fit by model.

This retainer clip secures a component in place to prevent movement and maintain proper alignment during appliance operation. Replacing a damaged or missing clip helps restore safe, reliable performance.

• Holds the mating part firmly to reduce vibration and noise
• Helps prevent intermittent operation caused by loose fitment
• Common fix when a component feels loose, rattles, or won't stay seated

• Disconnect power and shut off gas/water before servicing
• Note original clip orientation and location before removal
• Use needle-nose pliers to carefully release and install the clip
• Do not over-bend the clip; replace if deformed or fatigued

Color: White.

This motor connector housing is the molded body that holds the motor's wire terminals for a secure, insulated connection. Replacing a cracked or heat-damaged housing helps restore reliable motor operation and prevent intermittent power issues.

• Organizes and insulates the motor's wiring terminals
• Locks the harness to the motor for a firm electrical connection
• Helps reduce loose contacts, arcing, and heat damage at the plug
• If the housing is failing, you may see intermittent or no motor operation, the machine stopping mid-cycle, or visible melting/discoloration at the motor connector

• Disconnect power; also shut off gas supply
• Note wire positions; transfer terminals into the new housing one at a time to maintain orientation
• Inspect terminals and wiring; replace any burnt or loose terminals before reassembly
• Ensure the connector seats fully on the motor and the harness is secure; restore power and test

This is the heater housing box that directs heated air from the heating element into the dryer drum. It forms an enclosed duct pathway to ensure proper airflow during the drying cycle. Replace this part if the dryer is not heating efficiently, takes too long to dry clothes, or the housing is cracked, warped, or damaged from excessive heat.

This signal switch controls the appliance's buzzer/alert level, letting the unit sound or change beeper volume so you can hear end-of-cycle or error alerts. It replaces a failed or intermittent buzzer control for reliable audible notifications. What it does

• Sends the control board a signal to enable or adjust the buzzer/alert tones
• Restores audible end-of-cycle and error notifications when the original switch is worn or unresponsive
• Commonly replaces switches that feel loose, don't click, or fail to change the buzzer setting
• Works as the user-accessible control for enabling/disabling or adjusting buzzer functions

• One signal switch

• Disconnect power before servicing to avoid shock or damage
• Handle wiring and connectors gently; verify and match terminals before reconnecting
• Reassemble panels and test buzzer function before full reinstallation

This front bulkhead is the large panel that forms the front wall of the dryer drum compartment and supports the drum as it rotates. It typically includes the opening where clothes are loaded and may include a felt seal to prevent air leaks. Replace this bulkhead if it is warped, cracked, or if the drum seal surface is damaged - symptoms include unusual noises, clothes getting caught between the drum and panel, or heat escaping from the front of the dryer.

Replacement machine bolt for securing panels, brackets, and components in dishwashers, dryers, washers, and laundry centers. Restores fit if missing.

Replaces the cabinet back panel on your dryer. Needed when the original is cracked, damaged, or missing. Covers internal components and restores enclosure.

Rubber bumper. Color: Grey.

Front panel for dryers. Replaces cracked, dented, or damaged exterior panels. Installs on the front of the cabinet to restore appearance and structure.

Mounting bracket for dryer shunt assembly. Secures electrical shunt component to cabinet frame. Replace if cracked, bent, or missing hardware slots.

Color: White. Size: 1 qt. can. Acrylic appliance paint.