Kenmore Washer Dryer Combo 110.98764792 (11098764792, 110 98764792) Parts

This hose clamp secures a hose connection to prevent leaks and keep your appliance running smoothly. It provides a tight, reliable hold on the hose fitting so water or air stays contained during operation.

• Tightens around a hose and fitting to m
  This part fixes the following symptoms

  • Leaking

  See more...
  Do-It-Yourself Stories from Customers like You Water leak   Steven K. • New City , NY • August 10, 2018

  Took off cover, installed new parts. Read more

This screw and washer is an OEM replacement part used for Whirlpool washers. It is used to secure the lid switch. Each screw is sold individually. The screw measures approximately 1 inch.

Rear leveling foot assembly that supports the back of your laundry center. Replace if cracked, broken, worn, or missing to restore stability.

Supports the spin basket on the center post for smooth, quiet rotation. Replace if your washer is noisy, vibrating excessively, or has poor spin performance.

This replacement dispenser stores your dishwasher's detergent and rinse aid, then releases them at the proper time in the cycle. Restore consistent cleaning performance and help prevent leaks around the dispenser area with a fresh assembly. What it does

Replace your washer's anti-rattle clip to eliminate vibration noise and buzzing during cycles. Secures components with light spring tension. Confirm fit with your model number before ordering.

This agitator mover is the upper auger section of a dual-action agitator. It ratchets in one direction to drive clothes downward for proper turnover, helping restore effective wash action when the original mover is worn or damaged. What it does:

• Do-It-Yourself Stories from Customers like You Agitator broke   Daniel F. • Sugar Notch , PA • October 14, 2025

  Replaced agitator Read more

Rubber washer gasket for washer fill hose connections. Replace if worn or leaking at coupler adapter. Measures 1-1/16 x 5/8 inch. Verify fit with model.

Dryer lint screen door provides access to the lint filter. Replace if cracked, broken, or won't close properly. Verify fit with your model number.

This screw grommet anchors a screw in thin appliance panels so trim, covers, or consoles stay tight. It provides a snug, vibration-damping fit where a standard screw could loosen or strip over time.

• Creates a captive insert so a screw can secure

Size: 10-16 x 5/8 inch.

PC-144 agitator that moves and tumbles clothes during wash cycles to help loosen soil and distribute water and detergent. Replacing a worn or damaged agitator restores proper wash action and improves cleaning performance. What it does:

• Uses fins
  Do-It-Yourself Stories from Customers like You Whirlpool thin twin dual agitator was not working (model ltg6234dq1)   Matthew S. • Los Angeles , CA • June 15, 2017

  The splines inside the bottom agitator that are supposed to fit snug with the agitator shaft were worn down and couldn't catch the shaft anymore. I removed the entire agitator then pulled the top agitator part off of the lower agitator part. I then replaced the lower agitator with the new one I purchased and kept the old top agitator part (the top part was still in good condition and didn't need replacing, although I did replace the "agitator dogs" because they're very cheap and figured it... Read more

Vinyl door seal creates an airtight barrier to maintain proper temperature and prevent energy loss. Replace when worn, cracked, or causing drafts.

This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.

• Provides a countersunk, flush-mount

Used from harness to top.

Size: 8 foot long. This external washer drain hose is needed when there is more distance between the washer and the drain. Note: comes with 1.5" diameter clamp but hose is 1.25" in diameter; therefore you may need to order the 1.25" diameter clamp separat