Kenmore Washer Dryer Combo 110.98764792 (11098764792, 110 98764792) Parts

This idler pulley assembly keeps the drive belt properly tensioned and aligned so your appliance runs smoothly and quietly. Replacing a worn or seized idler restores reliable belt drive and helps prevent slippage, noise, and no-drive issues.

• Maintains spring-loaded tension on the drive belt
• Spins freely to reduce friction and belt wear
• Helps route and align the belt between the motor and drum/basket
• Typical symptoms of a failing idler: squealing/chirping, belt fraying or coming off, intermittent or no tumble/spin, burning rubber smell

• Disconnect power; for gas units, also shut off the gas supply.
• Relieve belt tension, swap the assembly, and route the belt per your unit's diagram.
• Rotate the drum/basket by hand to check alignment.
• Wear cut-resistant gloves and use caution around sharp edges and spring tension.

Size: 5 foot long. Rubber fill hose used on most automatic washing machines. Two hoses used per machine.

This lint screen traps fibers and debris as air circulates through the dryer. A clean, intact screen helps maintain airflow, improve drying performance, and protect the blower and vent from excessive lint buildup.

• Captures lint and debris from laundry during drying
• Helps maintain proper airflow to reduce extended dry times
• Assists in preventing lint from entering the blower housing and vent
• Replace if mesh is torn, frame is warped, or screen no longer seats properly

• Unplug dryer before servicing
• Remove the old screen from the filter housing; clear any lint from the chute
• Insert the new screen fully so it seats flat and snug
• Clean the lint screen before or after each load to maintain performance

The door switch detects whether the dryer door is open or closed, enabling the motor and heater only when it's safe. Replacing a failed switch restores proper start/stop control and drum light behavior.

• Senses door position and completes or interrupts the dryer's run/heat circuits
• Shuts the dryer off when the door opens for safety
• Common symptoms: dryer won't start with the door closed; doesn't stop when door opens; drum light stays on or won't turn on
• Intermittent operation when the door is moved or pressed

• Disconnect power before servicing; allow components to cool
• Access the switch from the door opening or front panel; remove screws or release locking tabs
• Note wire positions and transfer them one at a time to the new switch
• Verify operation before reassembly: dryer should not run with the door open; drum light should respond

This motor shield covers the drive motor on top-load washers to deflect splashes, lint, and debris away from the motor and wiring. Replace a cracked or missing shield to help protect the motor assembly at the base of the machine. What it does:

• Covers the washer's drive motor to deflect incidental water and debris
• Helps protect motor windings and terminals from splashes
• Replaces a cracked, warped, or missing cover
• Common signs: visible damage, rattling from the base, or corrosion/debris buildup around the motor

• 1 motor shield

• Unplug the appliance and turn off water supply before servicing
• Access the motor area from the bottom of the cabinet; note the shield's orientation
• Remove the damaged shield and install the new shield fully seated, reusing existing fasteners/clips
• Confirm clearance from moving parts before restoring power and testing

10 - 16 x 1/2

This locking nut is used for many purposes on a range of machines including household appliances. This nut is often used for leg leveling for machines. It will help with vibrations from washers and dryers. If the nut is used for this purpose and goes missing or becomes damaged, it could cause the machine to vibrate more and seem louder.Nuts are made from metal and are built to last a long time. However, there can still be issues that arise. In some cases, the nuts might go missing if they become loose and the machine is moved. They could also corrode over time and need to be replaced. The replacement of the nut is typically a fast and simple repair.The nut is a genuine OEM replacement part sourced from the manufacturer. It can work with washers, dryers, and combo machines, and is compatible with models from Whirlpool, Kenmore, Maytag, and Roper. The part is sold individually. Owners may want to have several on hand.

Specs: 10-16 x 1/2 inch.

This top front lock secures the front edge of a lift-up range cooktop to the cabinet frame. Replacing a worn lock restores a flush, stable fit so the cooktop stays closed during everyday cooking and cleaning.

• Locks the cooktop down to prevent unintended lifting during use or cleaning
• Maintains alignment so the front edge sits flush and stable
• Reduces vibration and rattling from a loose or misaligned top
• Common symptoms: cooktop won't latch or stay down, front gap, rattling or movement

• Disconnect power and allow the appliance to cool; shut off gas supply if applicable
• Lift the cooktop to access the front frame, remove the old lock, and install the new lock in the same orientation
• Secure with the original fasteners and verify the lock fully engages the mating catch
• Close the cooktop and confirm a flush, stable fit

This part is a motor clamp. This is a genuine OEM part and has been sourced directly from the manufacturer. This part is intended to replace a deteriorated, damaged, or broken motor clamp on certain makes of indoor appliance models. Motor clamps are essential for properly securing the drive motor on various types of indoor appliances such as washers, dryers, and refrigerators. Without the use of a motor clamp, the drive motor is free to move around or become detached. This can easily cause serious damage to the equipment and prevent proper functionality. Proper tools are needed to replace this part and appropriate safety measures should be adhered to when working on any type of equipment. For accurate information on how and where to install this replacement motor clamp, specific manufacturer diagrams should be referred to.As an authentic replacement part, this motor clamp can be used on multiple different models of washers, dryers, refrigerators, and washer/dryer combos manufactured by Kenmore, Maytag, Whirlpool, and Amana. Please note that this motor clamp is a genuine part made of high-quality materials and is sold individually.

This tub ring mounts to the top of the washer's outer tub to act as a splash guard and cover. Replacing a cracked or loose ring helps contain wash water and helps prevent leaks or debris from the top. What it does:

• Forms the upper splash guard around the outer tub to keep water contained during wash and spin
• Serves as the top cover at the tub opening, locking in with tabs/clips
• Damage (cracks, broken tabs) may lead to leaks from the top, rattling, or a loose ring
• Visible wear can leave plastic fragments in the basket or around the tub opening

• 1 tub ring

• Disconnect power and turn off water supplies before servicing
• Lift or remove the top/console per model design to access the tub opening; support the lid
• Release the locking tabs/clips and remove the old ring; clean the tub lip
• Align and press the new ring evenly until all tabs fully engage; reassemble and test

Dryer motor used in washer/dryer stack units.

This replacement cap covers an opening or fastener on the appliance. It helps keep water, detergent, and debris out while restoring a clean, finished look and maintaining a secure fit. What it does:

• Covers and protects an exposed opening or fastener from moisture and debris
• Helps prevent residue from entering internal areas
• Restores the appliance's finished appearance
• Common signs of failure: missing cap, cracks, warping, or a cap that won't stay seated

• 1 cap

• Unplug the appliance; if working near water connections, turn off the water supply
• Carefully remove the old cap without prying against delicate surfaces
• Clean the mating area; align and press or twist the new cap until fully seated
• Verify a secure fit and normal operation

This retainer ring is a genuine OEM replacement part sourced directly from the manufacturer for use on front load washing machines to hold the boot seal in place. The boot seal is the gasket that seals the washing machine when the door is closed to prevent water from leaking. The retainer ring is located flush against the boot seal and has either a spring clamp or screw clamp that secures it. Over time, this ring may become damaged due to the washing machine's normal use and age. If the ring is not tight, the washing machine could leak when in use. If water is coming from the door, it is a good idea to inspect and replace the retainer ring and possibly the boot as well.Unplug the washing machine to prevent electrocution. Remove the front panel, the detergent dispenser, and the kickplate to access the retainer ring. Locate the clamp on the ring and loosen it. Remove the retainer ring and set it to the side. Inspect the boot and then install the new retainer ring. Tighten the clamp and reassemble the washing machine. This retainer ring is sold as an individual unit. It is designed specifically for washing machines manufactured by Whirlpool.

This motor retainer secures the motor to its mounting point, keeping the assembly tight and aligned. Replace a worn or broken retainer to cut vibration and noise and to protect nearby seals, wiring, and components. What it does:

• Holds the motor firmly in place within the assembly
• Maintains alignment for smooth, quiet operation
• Supports sealing surfaces and connections; on water-bearing assemblies, help prevent leaks
• Replace if you notice a loose or rattling motor, new vibration/noise, or signs of movement or leakage at the motor

• Includes 1 motor retainer.

• Disconnect power; turn off water supply.
• Access the motor area and support the motor before removing the old retainer.
• Inspect mating parts and seals; replace any damaged components.
• Fully seat the motor and install the new retainer securely; test for abnormal noise or leaks.

This anti-rattle screw secures panels or brackets to prevent vibration noise in compatible appliances. Replacing a missing or stripped screw restores a tight fit and helps keep the cabinet and assemblies stable and quiet.

• Secures brackets, ducts, or panels to reduce buzzing and rattling during operation
• Replaces a lost, worn, or damaged anti-rattle fastener
• Helps maintain proper alignment and prevents vibration-related wear
• Typical symptoms include persistent rattling, a loose panel, or hardware found inside the cabinet

• Disconnect power before servicing; for gas appliances, shut off the gas supply
• Access the mounting point and remove the loose or damaged screw
• Start the new screw by hand to avoid cross-threading; tighten snugly without overtightening
• Repair or replace the bracket/clip before reassembly