Kenmore Refrigerator 253.36801893 (25336801893, 253 36801893) Parts

Replacement mounting screw for securing brackets, trims, covers, and components inside your refrigerator. Replace missing, stripped, or lost hardware.

Secures panels, brackets, and handles in refrigerators and other appliances. Replace missing or stripped screws to restore secure mounting.

This compressor start device kit helps your refrigerator or freezer's compressor start reliably each cooling cycle. Replacing a weak or failed start device can restore cooling performance and stop repetitive clicking or brief humming when the compressor tries to start.

• Powers the compressor's start winding to initiate start-up, then disengages
• Supports consistent compressor starts to maintain proper temperatures
• Common symptoms of failure: unit warm, compressor not running, rapid clicking from rear, humming then shuts off
• May accompany signs like heat damage or a burnt odor at the old device

• Unplug the appliance before servicing; allow components to cool
• Located on the side of the compressor behind the rear access panel
• Photograph wiring and compressor pin layout; transfer wires one at a time and seat the device fully on the pins
• If your unit uses a separate run capacitor, reconnect it exactly as originally wired

Replace a cracked, broken, or missing refrigerator crisper pan. This drawer installs in the fresh food compartment to hold produce and keep shelves organized.

Aluminum strap secures the defrost heater against the evaporator coil. Replace if broken, cracked, or missing to maintain proper heater contact.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Replacement screw for securing panels, brackets, and covers on appliances. Replaces missing, stripped, or damaged screws to restore alignment.

Factory fastener that secures panels, brackets, and internal components. Replace missing, stripped, or corroded screws to restore tight fit and eliminate rattling.

Optional flexible ice tray for those that dont have an icemaker

White plastic button plug that covers unused hinge holes on refrigerator doors. Replace if cracked, missing, or discolored for a clean finished look.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

Center hinge pin that secures and aligns the middle door hinge on your refrigerator. Replace when worn, damaged, or missing to restore door support.

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

Pan head screw for refrigerator assembly and panel mounting. Replace missing, stripped, or loose screws to secure components and maintain structural integrity.

Sound dampening foam pad for refrigerators and freezers. Installs on evaporator or compressor area to reduce vibration noise. Replace if worn or missing.