Kenmore Refrigerator 253.44333608 (25344333608, 253 44333608) Parts

This replacement cover restores a clean, finished look and protects internal components inside your refrigerator. Replace a broken or missing cover to keep parts secured and the compartment properly enclosed for dependable everyday use.

• Conceals and protects internal components or hardware in the designated area
• Restores a secure, finished enclosure over the section it covers
• Common failure signs: cracked, warped, or missing cover
• Won't snap or stay in place; loose or rattling piece
• Exposed screws/hardware or items snagging on the opening

• Unplug the refrigerator before servicing
• Clear food items/shelves as needed to access the cover
• Release retaining tabs or remove mounting screws; transfer any reusable hardware
• Align and snap or fasten the new cover; verify secure fit before restoring power

This freezer door gasket forms the airtight seal between the freezer door and cabinet. Replacing a worn or damaged seal helps keep cold air in, reduce frost buildup, and restore proper temperatures and efficiency.

• Creates a tight perimeter seal to prevent warm air leaks and moisture intrusion
• Helps maintain stable freezer temperature and humidity
• Reduces frost and ice accumulation around the door area
• Common symptoms: visible gaps or tears, door not sealing fully, condensation at the door edge, heavy frost near the door

• Disconnect power before servicing
• Warm the new gasket (soak in warm water or use gentle, low heat) to relax and ease installation; do not overheat
• Remove the old gasket; seat the new gasket fully into the door channel (some models require loosening and retightening retainer screws)
• Verify an even seal all around; perform a paper/dollar-bill test and adjust corners as needed

A single replacement mounting screw used to secure appliance panels and components. Restores proper fit and prevents rattling or loose parts so trims and panels stay aligned during normal use. What it does:

• Fastens panels, brackets or trim pieces to the appliance frame
• Replaces worn, stripped or missing screws that cause loose or rattling parts
• Helps restore secure alignment for doors and access panels
• Works where the OEM lists a basic machine/fastener screw

• Disconnect power and water before beginning any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Thread by hand to start, then tighten until snug—do not overtighten
• Keep small parts away from children and pets during installation

A replacement hanger basket that supports items inside the appliance so clothes or components stay organized and secure. Restores proper basket support and helps prevent sagging or shifting during operation. What it does:

• Holds and supports garments or items in the appliance basket area
• Helps maintain even load distribution to reduce rubbing or snagging
• Can resolve symptoms like a loose, tilted, or missing basket support
• Replaces worn or damaged hanger/basket hardware

• One hanger basket

• Disconnect power before inspecting or replacing parts
• Remove surrounding panels or components as needed for access
• Use basic hand tools; handle sharp edges carefully

This evaporator cover mounting bracket secures the evaporator cover inside the freezer compartment to keep cooling airflow and components in place. Durable metal construction replaces a broken or bent bracket to restore proper cover alignment. What it does:

• Holds the evaporator cover in position for correct airflow and protection of the evaporator coil
• Helps stop rattling or loose cover movement that can cause noise
• Restores a secure mounting point after impact or corrosion damage
• Works with the evaporator cover assembly to maintain consistent cooling performance

• High-level replacement: remove the evaporator cover to access mounting points; fasten bracket with existing screws
• Use basic hand tools; keep screws and clips organized for reassembly
• Disconnect power to the appliance before starting any repair to avoid electrical hazard

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

This screw set contains the fasteners used to secure panels and components on compatible Frigidaire appliances, helping restore proper fit and reduce rattling or loose parts. Replace missing or worn screws to re-secure covers and mounts. What it does:

• Provides the correct fasteners for reattaching trim, panels, or internal components
• Restores secure mounting to reduce vibration, rattling, or loose panels
• Replaces missing or damaged screws that prevent proper assembly
• Helps ensure service repairs use the correct OEM-style hardware

• One screw set

• Use the screws only in the specified locations and quantities recommended by your service guide
• Tighten screws snugly but avoid over-torquing to prevent stripping or damage
• Disconnect power (and water, if applicable) before servicing the appliance
• If any fastener appears damaged or the fit is incorrect, stop and verify fit before completing the repair