Kenmore Refrigerator 253.44353406 (25344353406, 253 44353406) Parts

This gray, magnetic freezer door gasket seals the perimeter of the door to keep cold air in and moisture out, helping maintain proper temperatures and reduce frost buildup for dependable food preservation.

• Forms an airtight magnetic seal between the freezer door and cabinet
• Helps stabilize internal temperature and humidity to limit frost and ice
• Common signs of failure: cracks or warping; condensation around the door; frost near the gasket; door not closing flush
• Restores sealing performance when the original gasket hardens or shrinks

• Unplug the refrigerator before servicing; use caution around sharp edges
• Warm the new gasket (warm water or low heat) to make it pliable
• Seat corners into the door retainer first, then work along the sides for an even fit
• Verify an even seal all around (dollar-bill test) and adjust gasket or door alignment as needed

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This dairy door is the flip-up cover for the refrigerator's dairy compartment on the fresh-food door. It keeps butter and cheese covered and contained, restoring a clean, finished look when the original cover is cracked or missing.

• Covers the dairy compartment and hinges open for easy access
• Helps keep small dairy items contained and organized on the door
• Replaces a cracked, warped, discolored, loose, or missing cover
• Closes properly when seated on the original hinge posts

• Disconnect power before servicing
• Remove the old cover by releasing its tabs from the hinge posts
• Align the new cover with the hinge posts and press to snap into place
• Avoid forcing brittle plastic; allow the part to reach room temperature before installation

A replacement fixed round blade that restores the appliance's original blade function and helps reduce vibration, noise or uneven performance caused by a worn or damaged blade. Use this OEM component for a proper fit and reliable operation. What it does

• Replaces a worn, bent or damaged fixed round blade to restore intended blade performance.
• Restores balance and smooth operation to the rotating assembly.
• Can reduce noise, wobble or uneven operation associated with a damaged blade.
• Matches OEM fit and function to help ensure correct alignment.

• Disconnect power to the appliance before beginning any work.
• Handle blade edges carefully; wear cut-resistant gloves if available.
• Remove and install per the appliance service manual or OEM instructions.

This genuine replacement clip secures appliance components to keep panels and small parts aligned and stable, restoring fit and function. It's a small, durable fastener used where a simple snap or hold is required. What it does

• Holds trim, panels, or small components in place to prevent rattling or misalignment
• Restores secure fit where a damaged or missing clip causes loose parts
• Helps stop vibration noise caused by unsecured pieces
• Small, direct-fit part—replaces a single broken or lost clip

• Disconnect power to the appliance before starting any repair.
• Access may require removing trim or panels; keep track of fasteners.
• Press or snap the clip into place; do not force beyond fit—if it won't seat, recheck alignment.
• Wear gloves and eye protection to avoid cuts from sharp edges.

A replacement clamp that secures flexible hoses or tubing to fittings to help prevent leaks and keep connections tight. Fits where a small spring-style or band clamp is used on water or drain hoses. What it does

• Holds hoses or small tubing firmly to appliance fittings to maintain a sealed connection
• Helps stop leaks and reduce movement that can wear or disconnect hoses
• Commonly used on drain and water line connections where a compact clamp is needed
• Works with flexible rubber or plastic hose materials; choose correct size for a secure fit

• One clamp

• Disconnect power and shut off the water supply before beginning work
• Drain residual water from hoses to avoid spills
• Use appropriate pliers or a screwdriver depending on clamp type; avoid over-tightening
• Inspect hose ends and fittings for damage and replace any worn components for a reliable seal