Kenmore Refrigerator 253.44359401 (25344359401, 253 44359401) Parts

This coil cover seal is a molded gasket that fits around the evaporator/coil cover to help keep airflow directed and reduce moisture and frost buildup. It restores the cover's sealing surface for more consistent cooling performance. What it does:

• Seals the evaporator/coil cover to help maintain proper airflow through the coil
• Helps reduce frost or ice buildup by keeping moist air away from cold coil surfaces
• Can prevent water dripping or pooling inside the cabinet near the coil
• Restores a tighter seal after a cracked, torn, or compressed gasket reduces effectiveness

• Disconnect power to the appliance before starting any repair
• You may need to remove the evaporator/coil cover or access panel to reach the seal
• Clean the mating surfaces and dry thoroughly before installing the new seal
• Handle the gasket gently and press evenly to seat; avoid stretching or sharp tools that could damage the part

This electronic console control replaces a failed or unresponsive control module so your appliance can send and receive commands reliably. It restores user input and cycle control for normal operation. What it does:

• Serves as the main control interface to manage cycles, timing, and functions
• Interprets button/knob inputs and sends signals to motors, valves, and heaters
• Prevents erratic behavior caused by failed or damaged control electronics
• Commonly used when displays, lights, or cycle selection stop responding

• One electronic console control module

• Disconnect power before attempting replacement to avoid shock or damage
• Handle the board by edges; avoid touching electronic components or solder joints
• Check connectors for proper seating and secure mounting per service manual

Left hand side. For the right hand side order 241674402

This spring-style hose clamp secures flexible appliance hoses and helps prevent leaks by holding hose ends tightly to fittings. Reliable, low-profile design for use on drain, water, or vent hoses where a strong, consistent grip is needed. What it does:

• Provides a spring-tensioned grip to keep hoses seated on fittings and reduce leaks
• Commonly used on flexible drain or water hoses and small vent lines
• Helps maintain proper connection under normal vibration and thermal cycling
• Replaces worn, stretched, or corroded clamps that no longer hold tension

• One spring hose clamp (exact quantity as sold)

• Use pliers to expand the clamp, slide into position, then release to seat on the fitting
• Inspect hose ends and fittings for wear; replace hose if damaged before installing clamp
• Wear eye protection when compressing the clamp; keep fingers clear of the clamp's edges
• Tighten only as needed—over-compressing can damage the hose

This is a factory-style replacement screw used to secure appliance components. It restores proper fastening where the original screw is missing, stripped, or damaged so panels and assemblies stay firmly attached. What it does:

• Fastens panels, brackets, or components to the appliance frame or assemblies
• Replaces missing or damaged mounting hardware that can cause rattles or loose parts
• Provides the correct fit and thread engagement for a secure connection
• Helps maintain appliance alignment and safe operation

• Use the matching screwdriver or bit to avoid stripping the head
• Tighten until snug; do not over-torque to prevent thread or part damage
• Turn off power and remove any access panels before working on electrical components

The Wiring Harness is an OEM part for Frigidaire refrigerators. It connects various electrical parts within the refrigerator, ensuring proper communication and voltage.

A bad wiring harness can be caused by wear and tear, damage, or electrical issues. Signs of a faulty wire harness include malfunctioning or non-functional parts, intermittent electrical problems, or loose connections.

Symptoms of a bad wiring harness can include:

• Intermittent electrical issues or power loss
• Burnt or melted wires
• Visible damage or wear on the wire harness

Replace your worn or damaged wiring harness with this genuine OEM part to restore your refrigerator. This Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.
 

This ice cream shelf rail secures the small shelf/bin on the freezer door so tubs and containers stay in place. It restores the door bin edge that holds lightweight frozen goods and keeps items from shifting during normal use. What it does:

• Replaces a cracked, broken or missing freezer door rail that allows containers to fall or tip
• Provides a stable lip for ice cream tubs, butter, and other small frozen items
• Helps restore proper fit and appearance of the freezer door storage area
• Fits into the existing door bin mounting points and holds the bin edge securely

• One ice cream shelf rail

• Unplug the appliance or shut off power before servicing to avoid electrical hazard
• Remove the door bin or ice cream shelf per your model's instructions to access the rail
• Typically snaps or screws into place; keep original fasteners if present and reuse when possible

This hanger-shelf glass is the replacement glass support used to hold and stabilize a refrigerator shelf. It restores a secure, level surface for stored items and replaces cracked or missing shelf supports. What it does:

• Supports and secures the refrigerator glass shelf to its hanger/rail
• Keeps the shelf level to prevent stored items from sliding or tipping
• Replaces broken, cracked or worn hanger supports that cause shelf instability
• Helps restore proper shelf alignment and safe storage inside the compartment

• One hanger-shelf glass replacement

• Handle glass carefully and wear cut-resistant gloves to avoid injury
• Remove shelf contents and the damaged shelf before installing the replacement
• Follow the appliance manufacturer's instructions for re-seating the glass into the hanger/rails