Kenmore Refrigerator 253.44359401 (25344359401, 253 44359401) Parts

Right hand side. For the left hand side order 241674401

This wiring harness routes power and signal connections between components to restore proper electrical communication and operation. It replaces a damaged or worn harness to fix intermittent or failed electrical functions. What it does:

• Reconnects power and control circuits between components so systems can receive proper voltage and signals
• Commonly used when wiring is frayed, burned, pinched, or connectors are loose or corroded
• Can resolve symptoms like no power to a component, intermittent operation, or control not responding
• Restores secure plug-and-play connections when the original harness is damaged

• Wiring harness assembly

• Always disconnect power before replacing any wiring or electrical parts
• Inspect connector fit, wire routing, and strain reliefs; route harness the same way as the original to avoid pinching
• Make sure connectors are fully seated and any locking tabs engage
• If you see damaged connectors on the appliance side, repair those before connecting the new harness

This control rod bracket secures the control rod to the appliance, restoring proper linkage and part alignment for reliable operation. Designed to replace a worn or broken mounting bracket and stabilize control movement. What it does:

• Holds the control rod in place so levers and linkages operate smoothly
• Restores proper alignment when the rod is loose, bent, or detached
• Helps eliminate binding or intermittent actuator movement caused by a damaged bracket
• Supports consistent mechanical operation of the connected control components

• One control rod mounting bracket

• Disconnect power to the appliance before beginning any repair to avoid shock or injury
• Remove any panels or covers as needed to access the bracket; keep fasteners organized for reassembly
• Inspect adjacent linkage and fasteners; replace any damaged clips or screws for a secure fit

This gray, magnetic freezer door gasket seals the perimeter of the door to keep cold air in and moisture out, helping maintain proper temperatures and reduce frost buildup for dependable food preservation.

• Forms an airtight magnetic seal between the freezer door and cabinet
• Helps stabilize internal temperature and humidity to limit frost and ice
• Common signs of failure: cracks or warping; condensation around the door; frost near the gasket; door not closing flush
• Restores sealing performance when the original gasket hardens or shrinks

• Unplug the refrigerator before servicing; use caution around sharp edges
• Warm the new gasket (warm water or low heat) to make it pliable
• Seat corners into the door retainer first, then work along the sides for an even fit
• Verify an even seal all around (dollar-bill test) and adjust gasket or door alignment as needed

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This dairy door is the flip-up cover for the refrigerator's dairy compartment on the fresh-food door. It keeps butter and cheese covered and contained, restoring a clean, finished look when the original cover is cracked or missing.

• Covers the dairy compartment and hinges open for easy access
• Helps keep small dairy items contained and organized on the door
• Replaces a cracked, warped, discolored, loose, or missing cover
• Closes properly when seated on the original hinge posts

• Disconnect power before servicing
• Remove the old cover by releasing its tabs from the hinge posts
• Align the new cover with the hinge posts and press to snap into place
• Avoid forcing brittle plastic; allow the part to reach room temperature before installation

A replacement fixed round blade that restores the appliance's original blade function and helps reduce vibration, noise or uneven performance caused by a worn or damaged blade. Use this OEM component for a proper fit and reliable operation. What it does

• Replaces a worn, bent or damaged fixed round blade to restore intended blade performance.
• Restores balance and smooth operation to the rotating assembly.
• Can reduce noise, wobble or uneven operation associated with a damaged blade.
• Matches OEM fit and function to help ensure correct alignment.

• Disconnect power to the appliance before beginning any work.
• Handle blade edges carefully; wear cut-resistant gloves if available.
• Remove and install per the appliance service manual or OEM instructions.