Kenmore Refrigerator 253.44393402 (25344393402, 253 44393402) Parts

This clear plastic drawer slides into the refrigerator compartment and serves as the dedicated meat or deli storage bin. It helps maintain a slightly cooler microclimate for perishable items like deli meats and cheeses. Replace it if the drawer is cracked, cloudy, or the slide mechanism is broken, preventing it from opening and closing smoothly.

Fix a fridge that has power but won't cool. This inverter board controls your compressor motor and regulates cooling. Moderate DIY repair in 1-2 hours.

Touch-up paint for appliances to cover scratches, chips, and worn areas on exterior surfaces. Restores appearance of refrigerators, ranges, and more.

Replaces the refrigerator's outer front plate when cracked, dented, rusted, or worn. Restores finished appearance and covers internal components.

This is the plastic ice storage bucket that sits beneath the ice maker in the freezer compartment to collect and hold ice cubes. It slides in and out for easy access to ice. Replace it if the bucket is cracked, warped, or if the handle is broken, which can cause ice to spill or make the bin difficult to remove.

This micro switch detects door or lid position and tells the appliance when the door is closed so cycles can start or safety interlocks stay engaged. It restores reliable door sensing and helps prevent operation with the door open. What it does:

• Acts as a position sensor that completes or breaks the control circuit when the door/lid is closed or opened
• Keeps the appliance from starting or continuing a cycle if the door is open (safety interlock)
• Common symptom fix: appliance won't start, stops mid-cycle, or shows door-related error codes
• Small electrical switch designed to mount at the door latch or frame and connect to the appliance wiring harness

• Disconnect power (unplug or shut off breaker) before attempting service
• Access may require removing panels, trim, or the door latch assembly; keep track of screws and fasteners
• Observe wiring orientation and connector positions; replace exactly as removed or tag wires

Reduces chlorine, lead, parasites, and VOCs in your refrigerator's water and ice. Replace every 6 months for optimal performance. Verify fit by model number.

Refrigerator door shelf cover that snaps onto door bin rails. Replace this plastic cover if cracked, broken, or missing to restore a clean appearance.

Creates an airtight seal around your refrigerator door to keep cold air in and prevent frost buildup. Replace if torn, cracked, or loose. Confirm fit.

Refrigerator drip pan installs under the cabinet to collect defrost and condensation water. Replace if cracked, broken, or missing to prevent leaks.

Positions and secures condenser tubing to maintain proper spacing. Replace if worn, broken, or missing to prevent vibration, rattling, and tube damage.

Replacement dairy door compartment for your refrigerator. Installs on the refrigerator door to hold butter, cheese, and small items. Order now.

Secures dairy compartment to refrigerator door. Replace missing, cracked, or broken lugs. Installs in door slots to hold compartment securely in place.

Left hand side. For the right hand side order 241674402

Right hand side. For the left hand side order 241674401

This solenoid actuator is the electromechanical device that moves a latch or linkage when energized, restoring the appliance's intended mechanical action. It provides a direct replacement to re-enable reliable actuation. What it does:

• Converts electrical signal into a mechanical push or pull to operate a latch, door, dispenser or linkage
• Commonly used where a timed or motor-driven movement is needed during a cycle
• Symptoms this part can cause: appliance fails to actuate a door, latch, dispenser or similar mechanism when called for
• Replacing a worn or failed actuator restores proper mechanical response to control signals

• One solenoid actuator

• Disconnect power to the appliance before beginning work to avoid shock or unintended actuation
• Remove any panels or trim as needed to access the actuator; note wire and mounting locations for reassembly
• Reconnect wiring and test the function on a short cycle after installation