Kenmore Refrigerator 253.44493704 (25344493704, 253 44493704) Parts

This gray, magnetic freezer door gasket seals the perimeter of the door to keep cold air in and moisture out, helping maintain proper temperatures and reduce frost buildup for dependable food preservation.

• Forms an airtight magnetic seal between the freezer door and cabinet
• Helps stabilize internal temperature and humidity to limit frost and ice
• Common signs of failure: cracks or warping; condensation around the door; frost near the gasket; door not closing flush
• Restores sealing performance when the original gasket hardens or shrinks

• Unplug the refrigerator before servicing; use caution around sharp edges
• Warm the new gasket (warm water or low heat) to make it pliable
• Seat corners into the door retainer first, then work along the sides for an even fit
• Verify an even seal all around (dollar-bill test) and adjust gasket or door alignment as needed

This replacement screw secures appliance panels, brackets, and internal components. It restores a tight, rattle-free fit and proper alignment when an original fastener is missing, stripped, or corroded.

• Fastens metal or plastic parts to the cabinet/frame
• Helps maintain alignment and reduce vibration or rattling
• Direct replacement for lost, damaged, or rusted hardware
• Keeps covers and brackets safely in place

• Disconnect power before servicing; for gas appliances, also shut off gas supply
• Match one-for-one with the original screw; verify length/type before installation
• Start threads by hand to avoid cross-threading; tighten snugly without overtightening
• Use the correct driver bit to prevent stripping the screw head

This dairy door is the flip-up cover for the refrigerator's dairy compartment on the fresh-food door. It keeps butter and cheese covered and contained, restoring a clean, finished look when the original cover is cracked or missing.

• Covers the dairy compartment and hinges open for easy access
• Helps keep small dairy items contained and organized on the door
• Replaces a cracked, warped, discolored, loose, or missing cover
• Closes properly when seated on the original hinge posts

• Disconnect power before servicing
• Remove the old cover by releasing its tabs from the hinge posts
• Align the new cover with the hinge posts and press to snap into place
• Avoid forcing brittle plastic; allow the part to reach room temperature before installation

A replacement fixed round blade that restores the appliance's original blade function and helps reduce vibration, noise or uneven performance caused by a worn or damaged blade. Use this OEM component for a proper fit and reliable operation. What it does

• Replaces a worn, bent or damaged fixed round blade to restore intended blade performance.
• Restores balance and smooth operation to the rotating assembly.
• Can reduce noise, wobble or uneven operation associated with a damaged blade.
• Matches OEM fit and function to help ensure correct alignment.

• Disconnect power to the appliance before beginning any work.
• Handle blade edges carefully; wear cut-resistant gloves if available.
• Remove and install per the appliance service manual or OEM instructions.

This spill-safe glass shelf replaces a cracked, chipped, or stained refrigerator shelf and helps contain spills for easier cleanup while restoring usable storage space. Ideal when a shelf no longer holds items securely. What it does:

• Replaces a damaged or missing refrigerator shelf so you can store items safely.
• Helps contain spills and drips on the shelf surface to limit mess to one area.
• Provides a flat, stable surface for food and containers.
• Restores original appearance and functionality to the shelf area.

• Remove all food and loose items from the shelf area before replacing.
• Carefully slide the shelf into the existing support rails or brackets until it seats securely.
• Handle the glass with care and wear gloves to avoid cuts during installation.

This genuine replacement clip secures appliance components to keep panels and small parts aligned and stable, restoring fit and function. It's a small, durable fastener used where a simple snap or hold is required. What it does

• Holds trim, panels, or small components in place to prevent rattling or misalignment
• Restores secure fit where a damaged or missing clip causes loose parts
• Helps stop vibration noise caused by unsecured pieces
• Small, direct-fit part—replaces a single broken or lost clip

• Disconnect power to the appliance before starting any repair.
• Access may require removing trim or panels; keep track of fasteners.
• Press or snap the clip into place; do not force beyond fit—if it won't seat, recheck alignment.
• Wear gloves and eye protection to avoid cuts from sharp edges.

Color: Black

This interior refrigerator glass shelf replaces a damaged or missing shelf, restoring a stable, easy-to-clean surface for storing food and containers. Its flat design helps keep items organized and visible. What it does:

• Provides a stable, flat surface for food, containers and small items.
• Replaces cracked, chipped, shattered or missing shelf glass.
• Easy-to-clean surface helps contain spills and reduce odors.
• Intended as a replacement for the factory shelf when installed on existing supports.

• Remove food and any loose items before removing or installing the shelf.
• Wear cut-resistant gloves and handle the glass by its edges to avoid injury.
• Slide or set the shelf into the existing tracks or ledges without forcing; ensure it sits level.
• If shelf clips, rails or supports are damaged, replace those parts separately before installing the glass.

This filter reduces parasites, lead, chlorine taste and odor, volatile organic compounds (VOCs), and some pesticides and pharmaceuticals. This genuine OEM replacement water filter is compatible with select Kenmore/Frigidaire counter-depth refrigerators. Replace every 6 months, or more often if water flow slows noticeably. Filter Media: Activated Carbon. Flow Rate: 0.5. Operating Temperature: 33 - 100 F. Operating Pressure: 30 - 100 psi. Meets NSF Standard: 42.

This drip tray catches and channels defrost and condensation water beneath the refrigerator to help prevent leaks and pool buildup under the appliance. Installs under the cabinet base where drain water collects during normal operation. What it does:

• Collects and holds defrost/condensation water from the evaporator drain.
• Directs water to the drain or evaporator to prevent leaks and floor damage.
• Reduces standing water that can cause odors or attract debris.
• Helps maintain normal drip/evaporation behavior after automatic defrost cycles.

• Disconnect power to the appliance before accessing or removing the tray.
• Remove the toe kick or access panel as required by your model to reach the tray.
• Empty any standing water and inspect for debris or damage before reinstalling.
• If the tray is cracked, warped, or shows excessive corrosion, replace to avoid leaks.