Kenmore Refrigerator 253.54739304 (25354739304, 253 54739304) Parts

This turntable roller assembly sits under the glass tray to support and guide it as it rotates. Replacing a worn or damaged ring helps restore smooth tray movement for more even heating and dependable microwave performance.

• Supports the glass tray and allows smooth, consistent rotation
• Helps prevent tray wobble, binding, or scraping noises
• Can address issues like the tray not turning or uneven cooking
• Replaces cracked, warped, or missing roller rings

• Disconnect power before servicing
• Remove the glass tray, lift out the old ring, and clean the cavity floor
• Place the new ring wheels-down, seat the tray on the coupler, and test rotation
• Do not operate the microwave without the roller ring and tray properly installed

An ice auger rotates inside the freezer's ice bin to move cubes to the crusher and out the dispenser chute. Replacing a worn or broken auger restores consistent dispensing and helps eliminate jams and grinding from a slipping spiral.

• Advances ice through the bin toward the crusher/dispenser chute
• Works with the crusher assembly to deliver cubed or crushed ice based on the selector
• A stripped or cracked auger may result in little/no ice dispensing while the motor runs
• Damage can cause ice jams, uneven dispensing, or grinding noises from the bin

• Unplug the refrigerator; remove and empty the ice bin, allowing any frost to thaw
• Wear cut-resistant gloves—crusher blades and sheet-metal edges are sharp
• Disassemble the crusher/blade stack and note the exact blade/spacer order
• Transfer the blade stack, bushings, and hardware to the new auger; reassemble and confirm smooth rotation before reinstalling

This humidity control is the adjustable slider in the crisper drawer cover that opens and closes the vent to regulate moisture around fruits and vegetables. Replace a cracked or missing control to restore smooth adjustment and consistent crisper conditions.

• Mounts to the crisper cover and links to the vent/damper door
• Slides between settings to increase or reduce airflow for proper crisper humidity
• Typical symptoms: broken or missing lever, slider stuck or loose, vent doesn't move as you adjust, excess condensation or wilting produce

• Disconnect power; remove food, crisper pan, and cover/glass as needed—handle glass carefully
• Release the old control from its slot/retainer and note the vent linkage orientation
• Seat the new control and engage the linkage; confirm full travel and proper vent action
• Reassemble the cover and drawer, then restore power

Specs: Hex head ,1/4-20 x 5/8

This drive cam is the rotating plastic cam used in the refrigerator's ice system. It transfers the motor's motion to linked parts to advance the cycle so ice can be produced and dispensed smoothly.

• Transfers rotation from the motor to move internal levers/gears in the ice assembly
• Advances the ice-making/dispensing cycle
• Wear or cracks can cause stalling, clicking/grinding, or no/weak ice dispensing
• May lead to ice not ejecting or jamming mid-cycle

• Disconnect power and shut off water before servicing
• Remove the ice bin; access the ice maker or dispenser mechanism as your model requires
• Note the cam's orientation and alignment marks; seat the new cam fully on the shaft
• Reassemble, restore power, and run a test cycle to confirm operation

This is not a filter. Use this bypasss if don't want to use the PureSource 2 Water Filter WF2CB or the Pure Advantage Water Filter EWF2CBPA.

This front shelf trim replaces a damaged or missing front edge on your refrigerator shelf. It restores a secure, finished lip that supports the shelf and helps keep items and small spills from sliding out.

• Attaches to the front edge of the shelf to provide a finished lip and added support
• Helps contain minor spills and prevents items from sliding off the shelf
• Resolves issues like cracked, warped, or missing trim and a loose or unstable shelf edge
• Common symptoms: broken or chipped trim, loose/missing front edge, shelf not seating or holding properly

• Remove food, lift out the shelf, and place it on a flat work surface
• Release the old trim by disengaging tabs and sliding/pulling it off
• Align the new trim with the front edge and press firmly until fully seated
• Handle shelf components carefully; wear protective gloves and disconnect power if working near internal electrical parts

This is a factory replacement screw fastener used to secure components in your appliance. It restores a tight, rattle-free fit for panels, brackets, and trim when an original screw is missing, stripped, or corroded.

• Secures panels, brackets, and trim to the appliance cabinet or liner
• Replaces a missing, stripped, or rusty screw
• Helps eliminate looseness, vibration, or rattling components
• Maintains proper alignment and a clean, factory fit

• Unplug the appliance before servicing; if near water lines, shut off the supply
• Match to the original and install in the same location/orientation
• Start threads by hand to avoid cross-threading; do not overtighten, especially into plastic
• Keep and reuse any original washers or spacers if present

This refrigerator bracket and bushing assembly secures a moving component and provides a stable wear/pivot surface for smooth operation. Replace it when the original parts are worn or broken and causing looseness, scraping noises, or poor alignment.

• Provides a mounting point and bearing surface for rotational or sliding movement
• Helps maintain alignment and smooth, quiet operation
• Can help address wobble, scraping/binding, or a component that sags or sits out of position
• Replace if the bracket is bent/cracked or the bushing is worn/missing

• Disconnect power before servicing; turn off water supply if working near dispenser lines
• Support the attached component while removing fasteners; note the original orientation
• Transfer any spacers/clips from the old parts if present and tighten fasteners evenly
• After installation, verify smooth movement and proper alignment

This aluminum strap secures the defrost heater firmly against the evaporator coil to maintain proper contact during defrost. Correct contact improves heat transfer so frost melts evenly and helps prevent recurring ice buildup on the evaporator.

• Secures the defrost heater to the evaporator for proper contact and heat transfer
• Promotes complete, even defrosting across the evaporator coil
• Helps reduce repeat frost/ice accumulation caused by a shifted or loose heater
• Typical clues include a loose heater, uneven frost pattern, or rattling near the evaporator

• Disconnect power and allow ice to melt before accessing the evaporator
• Use care around sharp fins and fragile refrigerant tubing; do not puncture or deform the coil
• Position the heater per your model's parts diagram and tighten the strap for firm, even contact
• Verify wiring is routed clear of the fan and moving parts before reassembly

Inlet valve filter

This refrigerator seal restores a tight barrier between internal components. Replacing a worn or damaged seal helps prevent air leaks and moisture intrusion, supporting proper airflow, stable temperatures, and reduced frost or condensation around the joint.

• Creates an air-tight barrier between mating surfaces
• Helps maintain correct airflow and temperature balance between compartments
• Reduces frost, condensation, and warm/cold spots near the sealed area
• Common signs of failure: visible gaps, loose/crumbled seal, rattling panel, moisture or frost at the joint

• Disconnect power before servicing
• Remove the related cover or housing to access the old seal
• Clean contact surfaces; install the new seal in the same orientation without stretching or pinching
• Reassemble and verify an even seal and normal airflow before returning to service

This fixed blade sits inside the refrigerator's ice bucket/crusher assembly. It provides a stationary cutting edge that works with the auger and rotating blades to break up cubes, helping your dispenser deliver consistent crushed ice.

• Stationary crusher blade that works with the auger and rotating blades to crush ice
• Helps prevent whole cubes from passing through on the "crushed" setting
• Worn, bent, or missing blades can cause poor crushing, jams, or uneven ice size
• May help address symptoms like dispenser jamming, irregular crushed ice, or increased grinding noises

• Unplug the refrigerator before servicing; remove and empty the ice bucket
• Note the order and orientation of blades, spacers, and fasteners; take reference photos
• Handle sharp metal edges; wear cut-resistant gloves
• Reassemble in the original sequence and tighten hardware snugly; ensure the auger turns freely before reinstalling

This small but critical actuator spring restores return tension in a refrigerator's actuator mechanism, helping the lever reset to neutral after use so controls feel responsive and operation stops cleanly. What it does:

• Provides the return force for an actuator or lever so it moves back to its neutral position
• Helps the mechanism engage/disengage a switch cleanly
• Common symptoms of a weak or broken spring: lever sticks, feels loose, or doesn't spring back
• Contribute to intermittent activation or failure to stop when released

• 1 actuator spring

• Disconnect power; if working near the dispenser/water system, shut off the water supply
• Access the actuator mechanism and note the spring's exact orientation (take a photo before removal)
• Use needle-nose pliers to transfer the spring; do not over-stretch or deform it
• Wear cut-resistant gloves and eye protection; test lever return action before reassembly