Kenmore Refrigerator 253.57399601 (25357399601, 253 57399601) Parts

This filter wrench is a ring-style tool used to loosen or tighten a refrigerator's water filter housing or canister. It provides extra leverage to free a stuck filter cup and helps ensure an even, secure reinstallation.

• Provides leverage to loosen a stuck water filter housing/cup
• Assists with secure, even tightening during reinstallation
• Useful when the housing is difficult to turn by hand
• Helpful in tight spaces where hand access is limited

• Turn off the water supply and dispense water to relieve pressure
• Position the wrench around the filter housing/cup; turn counterclockwise to loosen
• After replacing the filter, tighten the housing until snug—do not overtighten
• Restore water supply and check for leaks

Small spring that provides return tension for refrigerator actuator lever mechanisms. Replace if spring is broken, stretched, missing, or lost during repair.

Freezer drain tube that channels defrost water from the drain pan to the drip pan. Replace if cracked, leaking around the grommet, or causing floor leaks.

Covers the service opening on your refrigerator. Replace if cracked, broken, or missing to protect internal components and maintain a clean appearance.

Replacement screw that secures brackets, shelves, trim, panels, and covers inside your appliance. Install when the original is missing, stripped, or corroded.

Ice spilling inside freezer or dispenser not working? This ice container deflector guides cubes into the chute. Simple snap-in installation fix.

Covers the factory test opening on your refrigerator cabinet or liner. Replace if missing, cracked, or damaged to restore a finished look and seal.

Water inlet tube connects the water valve to your ice maker. Replace if cracked, leaking, or damaged. Installs at the back of your refrigerator.

Color: White

Seals internal refrigerator components to prevent air leaks and moisture intrusion. Replace when worn to maintain proper airflow and temperature control.

Spacer that fits between refrigerator door hinge components to maintain proper clearance and alignment. Replace if worn, cracked, or missing.

Specs: 1.40`` long

Fridge not cooling or making loud buzzing noise? This compressor kit restores cooling in refrigerators and freezers. Professional repair recommended.

This door hinge pin forms the pivot for the refrigerator door hinge, keeping the door supported and aligned. Replacing a worn or missing pin restores smooth door movement and consistent sealing.

• Acts as the hinge's pivot shaft to support the door
• Helps maintain door alignment so the gasket can seal properly
• Reduces wobble and scraping at the hinge point
• Typical failure symptoms: door sagging, misalignment, poor closing, or a loose/wobbly hinge

• Unplug the refrigerator and remove items from the door to reduce weight.
• Support the door; remove hinge cover and screws, then lift the door off the hinge.
• Replace the hinge pin in the hinge bracket; transfer any existing spacers/bushings as designed.
• Reinstall and align the door; tighten hardware and verify smooth operation and seal contact.

Replacement water inlet tube that connects the water valve to the inline filter. Needed when tube is cracked, leaking, or damaged. Runs along refrigerator back wall.

This E-ring is a small retaining clip used in Frigidaire refrigerators to hold components on a grooved shaft or pin. It keeps assemblies secure and operating smoothly by preventing parts from sliding off during normal use. What it does:

• Retains parts on a grooved shaft or pin to prevent axial movement
• Helps keep mechanisms aligned and reduces wobble or separation
• Common symptoms when missing or damaged: loose or fallen-off parts, scraping/rattling noises, or poor operation of the affected assembly

• 1 E-ring

• Unplug the refrigerator before servicing; wear eye protection (spring clips can snap)
• Use needle-nose pliers or an E-clip tool to compress and seat the ring in the groove
• Verify the ring is fully seated and flush in the groove before reassembly
• Keep any spacers/washers in the original order during removal and reinstallation