Kenmore Refrigerator 253.60744400 (25360744400, 253 60744400) Parts

Fixed rollers with leveling screw for the left hand side. For right side, order part 241889001.

This replacement egg tray restores organized egg storage in your refrigerator door or shelf area so eggs stay upright and easy to access. Durable molded plastic replaces cracked or missing trays to help keep eggs contained. What it does:

• Holds and secures eggs to prevent rolling and tipping
• Restores a missing or damaged egg storage area in the fridge
• Helps reduce mess from cracked or loose eggs
• Fits into the refrigerator door or designated shelf location

• Simply remove the old tray and snap the new tray into the existing mounting location
• No tools required for most installations; handle gently to avoid cracking the tray
• Clean with mild detergent before first use
• Keep away from high-heat sources and avoid harsh chemicals

Replacement screw that secures refrigerator door handles to the door. Needed when the original screw is worn, missing, or stripped, causing a loose handle.

Rubber grommet that mounts and cushions the compressor to reduce vibration transfer. Replace if cracked, worn, or missing to restore quiet operation.

Black rubber mounting grommet that secures tubes and wires in your refrigerator. Replace if cracked, worn, or missing to properly hold components in place.

The refrigerator ice maker hole plug is a rubber or plastic cap that seals the pre-drilled opening in the refrigerator cabinet wall that is used for ice maker water line connections. It keeps cold air from escaping through the unused hole in refrigerators that do not have an ice maker installed. Replace or install this plug if cold air is leaking through an open hole in the back wall of the refrigerator, causing temperature fluctuations or frost buildup.

Supports the compressor on the refrigerator's rear base. Replace if cracked, broken, or worn to keep compressor properly seated and reduce vibration damage.

Secures panels, trim, and brackets inside your refrigerator. Replace this #8-18 x 3/8 screw if the original is missing, stripped, or worn.

Rubber grommet cushions and seals freezer components, reducing vibration and preventing wear where wiring or rods pass through. Replace if cracked or worn.

Secures tubes and wiring in your refrigerator. Replace if clips are broken or connections are loose. Confirm fit with your model number.

Bisque-colored plug insert for refrigerator control panels. Replaces missing, cracked, or discolored button plugs to restore a clean appearance.

This heat exchanger suction line kit replaces a damaged or corroded suction line assembly to restore proper refrigerant flow and heat transfer in the cooling system. It helps maintain consistent compartment temperatures and system efficiency. What it does:

• Transfers heat from the refrigerant suction line so the compressor and evaporator operate correctly
• Replaces cracked, kinked, or corroded tubing that can cause refrigerant loss or reduced cooling
• Helps address symptoms such as warm or inconsistent temperatures, visible oil or residue at fittings, or abnormal frost/ice patterns
• Restores a sealed refrigerant path after tubing damage or when corrosion has compromised the line

• Intended for qualified service technicians only; system access requires certified refrigerant handling
• Disconnect power to the appliance before servicing and follow all safety precautions
• Installation may require brazing, flare fittings, or specialty tools; verify leak-tight connections and pressure-test per OEM procedures
• Evacuate and recharge the refrigerant system to OEM specifications after installation

Refrigerator not cooling or freezing properly? This evaporator coil kit restores cooling performance. Moderate DIY repair with basic tools required.

This is a replacement mounting screw used to secure the defrost timer assembly to the refrigerator control housing, restoring proper fastening and preventing the timer from shifting or vibrating during operation. What it does:

• Secures the defrost timer to the control housing so the timer stays in position.
• Prevents vibration or movement that can cause intermittent contact or noisy operation.
• Helps maintain reliable defrost cycle timing by keeping the timer properly aligned.
• Addresses symptoms such as a loose or missing fastener, rattling behind the control panel, or a timer that shifts when the door is opened.

• Unplug the appliance before starting work to prevent electrical shock.
• Access the control housing or timer bracket per your model's service instructions.
• Use the correct screwdriver or driver bit; do not overtighten—stop when snug to avoid stripping.
• Retain removed hardware for reference and compare screw length/threads before installing.

Plastic shelf cover that sits above the crisper drawers in your refrigerator. Replace if cracked, broken, or damaged to restore proper drawer support.