Kenmore Refrigerator 253.71112103 (25371112103, 253 71112103) Parts

This replacement rear compressor base roller supports the refrigerator compressor on the cabinet rear base, helping keep the compressor properly seated and reducing wear from vibration and movement. What it does

• Provides a rolling support under the compressor to keep it aligned and off the cabinet floor
• Helps reduce vibration and rattling that can occur from a loose or worn compressor mount
• Prevents compressor body from dragging or scraping the cabinet base
• Commonly replaced when the roller is cracked, worn flat, missing, or causing noise

• Disconnect power to the appliance before starting any work
• Support or secure the compressor and cabinet before removing the old roller to avoid sudden movement
• Basic hand tools usually required; inspect mounting hardware and replace any damaged fasteners
• Do not attempt sealed-system repairs.

This rubber grommet cushions and seals appliance components to reduce vibration and prevent wear where wiring, rods or panels pass through mounting openings. It helps keep parts aligned and protects against chafing and noise. What it does:

• Cushions and isolates vibration between moving parts and chassis
• Protects wiring, tubes or rods from rubbing and abrasion at mounting holes
• Helps reduce noise caused by contact or metal-on-metal vibration
• Aids in maintaining proper part alignment and secure fit

• Grommet

• Inspect mating hole and surrounding area for debris or sharp edges before installing
• Fit the grommet into the mounting hole so the flange seats evenly on both sides
• Replace any damaged or excessively worn grommets to restore protection
• Disconnect power and follow appliance safety procedures before attempting service

This rubber compressor mounting grommet cushions and isolates the compressor to reduce vibration and noise that can transfer to the cabinet. It helps maintain stable compressor positioning for quieter, smoother operation. What it does:

• Absorbs compressor vibration to lower noise and rattling
• Dampens movement that can cause abrasion or wear on mounting hardware
• Helps maintain proper alignment of the compressor assembly
• Common symptom: excessive buzzing, vibration, or rattling from the back of the appliance

• Always disconnect power to the appliance before servicing.
• Support the compressor before removing mounts to prevent shifting or damage.
• Inspect surrounding mounts and hardware; replace any worn or damaged pieces.

This control box houses and protects the appliance's electronic controls and wiring, restoring a secure mounting point for the console and control modules. Replacing a damaged control box helps resolve loose or exposed electronics and supports reliable button and display operation. What it does:

• Provides a secure enclosure for the control board and wiring harness
• Protects electronics from damage, debris, and shorting
• Restores proper mounting and alignment of the control console
• Can stop symptoms like loose or intermittently working buttons, exposed wiring, or a rattling console

• Disconnect power to the appliance before starting any work
• Replacement typically requires removing the control console or outer panel to access mounting screws and harness connections
• Handle electronics and connectors carefully; avoid forcing or bending housing tabs

This replacement screw secures select refrigerator door handles to the door. A worn or missing screw can leave the handle loose or detached, making the door difficult to open and potentially stressing other components.

• Holds the door handle firmly to the door
• Helps restore proper door operation and safe grip
• Designed to fit designated mounting points for compatible models

• Unplug the refrigerator before beginning work
• Open the door to access the handle mounting points
• Use the correct screwdriver/Allen tool to avoid stripping the head
• Start threads by hand and tighten snugly—do not overtighten

Color: Black. Rubber. Holds tube/wire

This condenser tube spacer positions and secures the refrigerator's condenser tubing to maintain proper tube spacing and airflow. Replacing a worn or broken spacer helps reduce vibration, rattling, and rubbing that can damage tubing over time. What it does:

• Holds condenser tubing in the correct position to preserve airflow and cooling efficiency
• Cushions tubing to limit vibration and reduce rattling noises
• Prevents tubing from rubbing against the cabinet or other components, lowering wear risk
• Helps reduce the chance of tubing fatigue that can lead to damage

• Disconnect power to the appliance before accessing rear panels or condenser components.
• Handle condenser tubing gently; avoid kinking, bending, or putting stress on lines during installation.
• Installation may require removing the back or lower access panel to reach the condenser assembly.

This shelf spacer is a genuine OEM replacement part sourced directly from the manufacturer, and it is used in refrigerators and freezers. This shelf spacer attaches to wire shelves in the refrigerator and freezer to hold them in place. If the shelf spacer is lost or damaged, the shelf will not stay in place. The spacer should be replaced.Refrigerator shelves must be sturdy to hold the weight of the food stored inside. If the shelf spacer is missing, the stability of the shelf is compromised. This part snaps onto the wire shelf and prevents it from moving around. This keeps the food inside the refrigerator from causing the shelf to fall. No tools are needed to install this part. If the shelf spacer is missing, do not store food on the shelf until it is installed.This shelf spacer is a white plastic part that is sold individually. It is designed for use in refrigerators manufactured by Kenmore, Frigidaire, Westinghouse, and Gibson.

This replacement tube routes water from the refrigerator's defrost area to the drain pan to help prevent leaks and pooling. A simple, direct-fit part for restoring proper drain flow and reducing water buildup. What it does

• Channels defrost and condensation water to the drain pan to prevent interior pooling.
• Helps maintain normal drainage to avoid ice buildup or water leaks.
• Restores a damaged, cracked or clogged original tube where flow is restricted.
• Works as a service part when inspecting drain path during defrost/drain issues.

• One replacement tube.

• Disconnect power to the appliance before starting any repair.
• Remove access panels as needed and route tube along the factory path; avoid sharp bends or kinks.
• Inspect drain openings and heater components while replacing the tube.

This defrost heater kit heats the evaporator to melt frost and ice buildup so the refrigerator can cycle normally and maintain proper cooling. It's a direct-replacement kit for units that use a heater-style defrost assembly. What it does:

• Warms the evaporator coil during the defrost cycle to remove frost and ice
• Helps restore normal airflow and cooling when frost buildup blocks the evaporator
• Commonly used when a refrigerator has excessive frost, poor cooling, or no active defrost
• Works with the existing defrost control and thermostat to allow automatic defrost cycles

• Disconnect power to the appliance before starting any service
• Handle evaporator fins and sharp sheet metal with care; wear gloves and eye protection
• Reassemble panels and restore power; check for proper defrost operation after installation

This genuine replacement screw secures panels and small components on select appliances, restoring fit and reducing rattles or loose parts. It's a direct-fit fastener where the original #8-18 x 3/8 screw is missing or worn. What it does:

• Fastens trim, panels or brackets to appliance frames and components
• Restores secure fit to stop rattling or misaligned parts
• Replaces stripped, rusted or missing screws that prevent proper assembly
• Matches original thread size and length for correct engagement

• Use the correct driver and engage threads straight to avoid stripping
• Do not overtighten; stop when the part is snug and secure
• Replace any damaged mating hardware for best fit
• Unplug the appliance or shut off power when accessing internal fasteners

This genuine replacement part is an evaporator used in refrigerators. The evaporator is the part that exchanges heat to cool the refrigerator. It is the component of the refrigerator that absorbs the heat from the air inside, turning it cool through absorption. If the refrigerator is no longer cooling properly, this could mean it's time for a new evaporator.This is a genuine replacement evaporator compatible with Frigidaire, Electrolux, Gibson, Kelvinator, and Westinghouse brand refrigerators.

Color: Black/natural. Nylon

This drain tube routes defrost and condensation water from the freezer compartment to the drain pan so moisture drains away cleanly and prevents pooling. Replaces a cracked, clogged or disconnected drain line. What it does:

• Channels defrost and condensation water out of the freezer to the drain system
• Prevents water pooling inside the freezer or refrigerator compartment
• Helps avoid leaks onto the floor when the original tube is cracked, pinched or disconnected
• Works with the appliance's drain trough and drain pan to maintain normal defrost drainage

• One drain tube

• Disconnect power before servicing and work with a cooled appliance to avoid burns
• Access may require removing interior panels or kickplate; handle panels and clips carefully
• Inspect and clear any debris or ice from the drain trough before installing the new tube
• Ensure the tube is routed without sharp bends or kinks and is securely seated at both ends