Kenmore Range 362.72208891 (36272208891, 362 72208891) Parts
Genuine Ge part
By: Ge
Part Number: WB56K10032
Insulation guard that installs inside the oven door assembly to protect internal components. Replace if cracked, torn, or missing during door maintenance.
More
Genuine Ge part
By: Ge
Part Number: WB8K1
This bulb housing assembly holds and protects the light bulb inside your oven or range hood while providing electrical connections. It secures the bulb in the correct position and shields it from heat, grease, and food splatter during cooking. Replace this housing if the interior light doesn't work, bulbs burn out frequently, or the housing is cracked or damaged.
Do-It-Yourself Stories from Customers like You
Oven would not light David A. • San Jose , CA • December 14, 2017
Control board, new oven light fixture, and receptacle along with the gasket. All I ever ask is get me the correct parts and AppliancePartsPros.com came through. Used them before to fix my gas dryer.
Cheers, David
Read more
More
Genuine Ge part
By: Ge
Part Number: WB2K65
Secures the gas safety valve to the chassis. Replace if worn, bent, broken, or missing to maintain proper valve alignment and stable positioning.
More
Genuine Ge part
By: Ge
Part Number: WB34K5
Protective wire cover for range burner igniter wires. Replaces cracked, broken, or missing covers. Shields wiring from damage inside the range cabinet.
Do-It-Yourself Stories from Customers like You
Degraded burner igniter wires Richard W. • Bakersfield , CA • August 19, 2016
Checked online instructions for range top ands rear upright removal. Cleaned inside surfaces before removing individual wires one at a time. Ran the new wires through retainers first, then to the correct igniters next. Replaced removed parts to restore.
Note: The remove the top burner screws from the cook top before trying to remove it. Otherwise, you will bend the burner gas supply tubes and possibly damage them if not done in sequence.
Utube mentioned using a screwdriver for the cook top...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB39K8
Left side broiler panel for gas ranges. Replaces cracked, damaged, or missing side panels. Mounts to the broiler compartment interior wall.
More
Genuine Ge part
By: Ge
Part Number: WB63K3
Genuine Ge part
By: Ge
Part Number: WB21K12
Fix a burner that won't light, leaks gas, or has a broken control stem. This gas valve regulates flow to one cooktop burner. Moderate DIY repair.
Do-It-Yourself Stories from Customers like You
Broken gas valve on gexl44 Diana F. • Fairfield , IA • July 18, 2014
Shut off gas. Order part from your helpful (on Sunday afternoon) telephone person. Get part in two days. Replace part.
Read more
More
$89.44
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB1X119D
$13.95
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB01K10008
Cooktop mounting screw secures the cooktop to frame or brackets. Replace if stripped, missing, or rusty to eliminate wobble, rattling, or lifted corners.
Do-It-Yourself Stories from Customers like You
Oven lock failed so self cleaning unit would not engage Alice L. • Martinez , CA • September 17, 2018
Replaced old lock and installed replacement lock and now have a happy wife.
Read more
More
$11.95
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB1K5
Size: 8-18 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Oven not lighting John D. • Orlando , FL • January 16, 2024
We replaced the igniter. To do the job right you need to pull the oven off the wall (this was the 6 burner with griddle dual oven). you need to get to the igniter plug by taking off the entire back.... easier than it sounds... the hardest part is sliding the stove out and back in... I only need a 1/4 in driver for the whole job.... it is easier if you take the oven doors off...
Read more
More
$9.95
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB28K10030
Burner orifice spud for gas range conversion between natural gas and LP. Replace broken, missing, or incorrect size orifices when converting fuel type.
Do-It-Yourself Stories from Customers like You
Propane to natural gas conversion on range and dryer Vincent P. • Howell , NJ • October 09, 2014
Confirmed parts needed through online chat with tech and followed video instructions for dryer conversion. Found a video online for range conversion. Replaced orifices for stove top and adjusted oven burner orifices and air shutters and inverted pin in pressure regulator to natural gas position. All went well with no problems, about an hour and a half to gather tools and complete both jobs. Probably could be done faster but I was taking my time.
Read more
More
$20.95
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB01K10003
Black mounting screw secures end caps on electric ranges. Replace missing, stripped, or damaged screws to properly fasten decorative end panels.
More
$8.76
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB07K10003
Black right-side end cap that finishes and secures trim, rail, or channel ends on your range. Replace if cracked, broken, or missing to restore fit.
More
$59.48
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB10K5
Right side broiler hinge for gas ranges. Replacement for broken, cracked, or worn hinges that keep the broiler door properly aligned and supported.
More
$11.68
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB10K6
Left side broiler hinge for gas ranges. Replaces broken, worn, or missing hinges that prevent proper broiler door operation and alignment.
More
$21.46
Out Of Stock
Usually ships within 4 - 14 days
Genuine Ge part
By: Ge
Part Number: WB1K62
This painted screw head is a cosmetic and protective cap that restores the finished look where a visible screw is used. It covers the screw head and helps match surrounding black trim for a clean appearance. What it does:
- Covers and conceals a screw head to improve appearance of panels, trim, or bezels
- Helps protect the screw head from direct exposure and reduces visible wear
- Used when trim or panels show exposed or mismatched screw heads
- Common fix when screw heads are scratched, discolored, or visually distracting
What's included: One painted black screw head. Install notes:
- Use the matching screw and press or snap the cap into place over the screw head
- Disconnect power and remove any panels only as recommended by your appliance manual before working near electrical components
- Avoid forcing or prying the cap; if tight, gently ease it on to prevent breakage
- Replace any damaged caps with the exact part to maintain fit and finish
More
$14.95
Out Of Stock
Usually ships within 4 - 14 days