Kenmore Range 362.7275591 (3627275591, 362 7275591) Parts
Genuine Ge part
By: Ge
Part Number: WB2K20
Anti-tip bracket kit installs to the floor behind your range or wall oven to prevent tipping. Replace if missing, damaged, or moving to a new home.
More
Genuine Ge part
By: Ge
Part Number: WB49K2
Do-It-Yourself Stories from Customers like You
Burned on pans Cheryl R. • Piney Creek , NC • October 30, 2015
New pans
Read more
More
Genuine Ge part
By: Ge
Part Number: WB7K5338
Do-It-Yourself Stories from Customers like You
End caps for oven door had broken and kept falling out Barbara L. • Roanoke , VA • January 05, 2019
Somewhat difficult to slide back on because pieces of the old tabs were stuck in the crevace, but once I realized and fished them out the next challenge was finally figuring out part went inside the crevace and part (a tab) went outside on the back of the handle. If you bend over and look up underneath it is easy to see how it goes, but apparently over the years the handle had gotten just out of shape enough that the caps did not readily slide on. Be careful you don't snap a tab or post off. ...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB7K5339
This handle cap is a replacement end cover that restores the clean finished look and protects the handle mounting on compatible refrigerators. It keeps the handle edges covered and helps prevent snags and cosmetic damage. What it does:
- Covers and protects the exposed end of a refrigerator door handle for a finished appearance
- Conceals handle mounting hardware and reduces dirt build-up around the handle area
- Helps prevent clothing snags and minimizes wear at the handle end
- Matches light white finish to blend with white appliance trim
What's included:
Install notes:
- Remove original cap by following the appliance manual; some models use hidden clips or a retaining screw
- Keep existing mounting hardware — this cap is a cosmetic cover and typically uses factory fasteners
- Avoid over-tightening clips or screws to prevent cracking the cap
Do-It-Yourself Stories from Customers like You
End caps for oven door had broken and kept falling out Barbara L. • Roanoke , VA • January 05, 2019
Somewhat difficult to slide back on because pieces of the old tabs were stuck in the crevace, but once I realized and fished them out the next challenge was finally figuring out part went inside the crevace and part (a tab) went outside on the back of the handle. If you bend over and look up underneath it is easy to see how it goes, but apparently over the years the handle had gotten just out of shape enough that the caps did not readily slide on. Be careful you don't snap a tab or post off. ...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB10K13
This support rivet securely fastens internal components within your range or oven structure. It provides structural stability for mounting brackets and panels inside the appliance. Replace this rivet if you notice loose parts rattling inside your oven or range components shifting during use.
More
Genuine Ge part
By: Ge
Part Number: WB2K11
Genuine Ge part
By: Ge
Part Number: WB2X1082
This retainer secures the oven door hinges in place and is located at the bottom corners of the oven door frame. Replace if the oven door sags, won't stay closed properly, or if the hinges appear loose or misaligned.
Do-It-Yourself Stories from Customers like You
Broken door hinge. Shari W. • Evansville , IN • February 07, 2018
By replacing the hinge.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB14K5
Pivot pin that connects the oven door hinge to its mounting bracket. Replace if worn, broken, or missing to restore smooth door operation and alignment.
More
Genuine Ge part
By: Ge
Part Number: WB24X415
Color: Black
Do-It-Yourself Stories from Customers like You
Old worn parts Billy S. • Newport News , VA • February 26, 2016
Easy removal of worn parts and easy installation of new parts.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB53K35
Do-It-Yourself Stories from Customers like You
The panel on the oven bottom was pitted and needed to be replaced Kenneth W. • Buffalo , MN • November 29, 2014
Simple as can be. Took 2 screws out, pulled out the old panel, and put the new one in. Done in five mintures
Read more
More
Genuine Ge part
By: Ge
Part Number: WB6K8
This metal bracket provides structural support for your range top, keeping it level and stable during cooking. It prevents sagging and maintains proper alignment of burners and cooking surfaces. Replace this part if your range top is sagging, uneven, or wobbles when pressure is applied.
Do-It-Yourself Stories from Customers like You
I replaced the cooktop in my range. Carol Z. • Bronx , NY • November 02, 2020
My 12 year-old cooktop was rusted through in a couple of key places, but the rest of my range was in terrific shape, so I decided to order a replacement cooktop. The perfect part arrived quickly. When I took a closer look at the few connecting parts I thought I was going to pirate off the old cooktop, I saw some were rusty, particularly the two Guide Slides and one screw. I needed to buy a set of star drivers, too, as a #10 was needed. I put a little WD40 on the parts I had to remove when I...
Read more
More
Genuine Ge part
By: Ge
Part Number: WB9K1
Do-It-Yourself Stories from Customers like You
Two springs on oven door were worn out William T. • Washington , DC • February 06, 2019
Replaced the oven door springs.
Read more
More
Genuine Ge part
By: Ge
Part Number: WB10K14
Genuine Ge part
By: Ge
Part Number: WB15K17
This metal grip allows you to safely pull out the broiler drawer for loading and unloading food. Located on the front of the broiler drawer beneath the oven, replace it if the handle is loose, broken, or becomes too hot to touch during use.
More
Genuine Ge part
By: Ge
Part Number: WB1K4
Genuine Ge part
By: Ge
Part Number: WB1X560D