Kenmore Dishwasher 363.1556991 (3631556991, 363 1556991) Parts
Genuine Ge part
By: Ge
Part Number: WD30X98
Replacement slide rail for dishwasher upper rack. Installs on cabinet wall to guide rack in and out. Needed when original is bent, twisted, or broken.
Do-It-Yourself Stories from Customers like You
Upper rack on dishwasher was very hard to extend and retract Daniel N. • Bolingbrook , IL • August 05, 2014
Dishwasher needed new wheel that mounted to upper rack.There are 4 total that make the rack roll in and out. Replaced both side rails and rail caps (4- only 50 cents each) along with new upper rack that came with wheels installed. One side rail was bent so decided to spend a little extra and replace both. Might of been able to replace just one broken rack wheel but rack was old and was rusting in some areas so decided to just replace it.
Read more
More
$55.95
- Compare At:
-
$66.58
- You Save:
-
$10.63
Genuine Ge part
By: Ge
Part Number: WD12X332
Includes screws.
Do-It-Yourself Stories from Customers like You
Worn out rollers due to old age of dishwasher. Budi N. • Madison , WI • March 09, 2018
Replace all 8 of them with the ordered parts. No big deal. Your provided repair-video was a big help! Thanks!
Read more
More
$11.95
- Compare At:
-
$14.22
- You Save:
-
$2.27
Genuine Ge part
By: Ge
Part Number: WH1X2036
Secures washer hoses at pump, tub, and valve connections to prevent leaks and hose blow-offs. Replace worn or missing clamps for a tight seal. Confirm fit.
Do-It-Yourself Stories from Customers like You
Drain hose was leaking Haide H. • Chatham Township , NJ • May 01, 2017
The video was very helpful. the hardest part is getting off old rusted parts. I had to use a hacksaw to remove one of the old clamps. I had to open the bottom of the washing machine to remove of the other clamp. Putting the new parts on was easy. Getting everything apart was a challenge. Putting the new parts on was an easy 5 minute job.
Read more
More
$15.95
- Compare At:
-
$18.98
- You Save:
-
$3.03
Genuine Ge part
By: Ge
Part Number: WD12X417
Protective cover that sits over your dishwasher's pump inlet to screen debris. Replace if cracked, broken, or missing to protect internal components.
Do-It-Yourself Stories from Customers like You
1 not draining properly 2 not cleaning properly 3 not filling properly 4 not running properly 5 sump and sump cap was filthy 6 James W. • San Diego , CA • March 19, 2017
1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve.
Parts $220 for Dishwasher
Estimated Labor $400.00
Labor $0.00
Parts $100.00 for Pullout Faucet
Estimated Labor $175.00
Labor $0.00
Read more
More
$26.95
- Compare At:
-
$32.07
- You Save:
-
$5.12
Genuine Ge part
By: Ge
Part Number: WD35X10011
White dishwasher lower spray arm assembly with collapsible tower. Replaces cracked, broken, or damaged spray arms. Installs at bottom of tub.
Do-It-Yourself Stories from Customers like You
1 not draining properly 2 not cleaning properly 3 not filling properly 4 not running properly 5 sump and sump cap was filthy 6 James W. • San Diego , CA • March 19, 2017
1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve.
Parts $220 for Dishwasher
Estimated Labor $400.00
Labor $0.00
Parts $100.00 for Pullout Faucet
Estimated Labor $175.00
Labor $0.00
Read more
More
$53.95
- Compare At:
-
$64.20
- You Save:
-
$10.25
Genuine Ge part
By: Ge
Part Number: WD28X10103
Replaces broken or cracked 3rd level spray arm assembly that mounts at the top of the tub. Includes mounting tabs and collar for secure installation.
Do-It-Yourself Stories from Customers like You
The top level (3rd level as called by ge/appliancepartspros) spray arm fell off Yuan S. • San Ramon , CA • June 27, 2014
There is a plastic "snapping" feature (Two plastic tabs that when pressed together can fit into the holes on the spray arm. Once in there, the tabs expands and keep the spray arm in place) that comes out of the top onto which the spray arm is attached to. That plastic piece broke and the spray arm fell off.
It wasn't clear how the snapping feature was attached to the top of the dishwasher at first. I was looking for a replacement for it and could not find it on any of the assembly diagram...
Read more
More
$55.30
- Compare At:
-
$79.84
- You Save:
-
$24.54
Genuine Ge part
By: Ge
Part Number: WD12X334
Fix dishwasher overflows or underfilling with a new water level float. This part regulates filling by rising with water to signal the switch.
Do-It-Yourself Stories from Customers like You
1 not draining properly 2 not cleaning properly 3 not filling properly 4 not running properly 5 sump and sump cap was filthy 6 James W. • San Diego , CA • March 19, 2017
1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve.
Parts $220 for Dishwasher
Estimated Labor $400.00
Labor $0.00
Parts $100.00 for Pullout Faucet
Estimated Labor $175.00
Labor $0.00
Read more
More
$12.49
- Compare At:
-
$14.74
- You Save:
-
$2.25
Genuine Ge part
By: Ge
Part Number: WD12X324
Detergent cup not opening during wash cycle? This actuator lever connects the timer to the dispenser lid. Moderate DIY repair, about 35 minutes.
This part fixes the following symptoms
-
Will not dispense detergent
See more...
Do-It-Yourself Stories from Customers like You
Defective timer John K. • Bear , DE • October 20, 2016
The timer was replaced. It took about 35 minutes. The most difficult thing was holding the door down.
Read more
More
Genuine Ge part
By: Ge
Part Number: WD1X1363
Metal contact leaf for dishwasher switch assemblies. Replace if the original contact is bent, corroded, worn, or missing to restore proper circuit closure.
More
$20.38
- Compare At:
-
$32.08
- You Save:
-
$11.70
Genuine Ge part
By: Ge
Part Number: WD21X479
This float switch detects rising water in the refrigerator drain pan or lower cabinet area and signals the appliance control to help prevent overflow and water damage. Use it to replace a failed or intermittent water-level sensor. What it does:
- Senses high water level in the drain pan or collection area and closes the circuit to alert the control.
- Helps identify causes of leaks and pooling under or behind the appliance.
- Commonly used when symptoms include water on the floor, drip pan overflow, or water-related error/alert conditions.
- Matches OEM function for refrigeration units that include a float-based water-detection circuit.
What's included: One float switch. Install notes:
- Disconnect power to the appliance before starting any repairs; shut off the water supply if working near water lines.
- Access may require removing lower kick plate or back panel; handle plastic clips and fasteners carefully.
- Disconnect electrical connector gently and note orientation before installing the replacement; secure wiring and verify float moves freely.
- Restore power and run a short test cycle or simulate water level to ensure proper operation.
Do-It-Yourself Stories from Customers like You
The dish washer was not fill with water Stanley B. • Newberry Springs , CA • December 14, 2014
1. Removed the water inlet/shut off valve, removed and cleaned the screen. while the valve was removed applied electrical power to the valve and it worked just fine.
2. replaced the broken float switch.
Read more
More
$71.95
- Compare At:
-
$85.58
- You Save:
-
$13.63
Genuine Ge part
By: Ge
Part Number: WD3X721
This spring kit restores proper door tension so the appliance door opens and closes smoothly and stays in position. Use it to replace worn or broken springs that cause a sagging, loose, or hard-to-operate door. What it does:
- Replaces worn or damaged door tension springs to restore smooth opening and closing.
- Helps prevent the door from dropping, sagging, or not staying open.
- Reduces uneven or jerky door movement caused by lost spring tension.
- Matches OEM-design function for safe, reliable door operation when installed correctly.
What's included: One spring kit. Install notes:
- Disconnect power (and water, if applicable) before beginning any repair.
- Springs are under tension—use caution and proper tools to avoid injury.
- Follow the appliance's service manual or OEM instructions.
More
$57.95
- Compare At:
-
$68.96
- You Save:
-
$11.01
Genuine Ge part
By: Ge
Part Number: WD12X10026
Replacement door vent directs humid air out during the dry cycle. Install inside the door panel to replace a cracked, clogged, or missing vent.
Do-It-Yourself Stories from Customers like You
Worn out tired dishwasher with some broken parts Laura C. • Black Canyon City , AZ • January 03, 2017
Found AppliancePartsPros.com and looked up parts and ordered replacement parts. ( VERY easy!) Replaced the spray arm assembly and door vent via the handy Q&A repair section, as well as a thorough cleaning, and VOILA! Clean dishes again!! Thanks for making it easy!
Read more
More
Genuine Ge part
By: Ge
Part Number: WD12X335
This float stem is part of the dishwasher's water-level/overfill system. It guides the tub float and actuates the float switch so the unit fills correctly and shuts off on time. Replace a worn or broken stem to restore reliable fill protection.
- Connects the float to the switch mechanism beneath the tub
- Provides smooth vertical travel of the float through the opening
- Triggers the float switch to stop filling at the proper level
- Causes symptoms such as no fill, continuous filling/overfilling, a stuck or wobbly float, or intermittent fill issues
What's included: 1 float stem Install notes:
- Disconnect power at the breaker and shut off the water supply before servicing
- Remove the lower rack; lift off the float cap from inside the tub
- On some models, release the retainer/clip from beneath the tub; pull out the old stem
- Guide the new stem through the opening and ensure it engages the float switch lever; confirm the float moves freely and actuates the switch before restoring power
Do-It-Yourself Stories from Customers like You
1 not draining properly 2 not cleaning properly 3 not filling properly 4 not running properly 5 sump and sump cap was filthy 6 James W. • San Diego , CA • March 19, 2017
1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve.
Parts $220 for Dishwasher
Estimated Labor $400.00
Labor $0.00
Parts $100.00 for Pullout Faucet
Estimated Labor $175.00
Labor $0.00
Read more
More
$28.28
- Compare At:
-
$30.43
- You Save:
-
$2.15
Genuine Ge part
By: Ge
Part Number: WD1X1392
Secures dishwasher sump to tub, maintaining seal compression to prevent leaks. Replace if corroded or weak. Confirm fit with your model number.
Do-It-Yourself Stories from Customers like You
Leaking pump connector. David M. • Ypsilanti , MI • October 13, 2018
Took the impeller out, removed the pump, replaced connector, put new clamps on, reassembled and checked for leaks. I just followed Arts video, went smooth. Wifes happy, things are good.
Thanks AppliancePartsPros.com
Read more
More
$15.95
- Compare At:
-
$18.98
- You Save:
-
$3.03
Genuine Ge part
By: Ge
Part Number: WD2X425
$6.72
- Compare At:
-
$8.36
- You Save:
-
$1.64
Genuine Ge part
By: Ge
Part Number: WD12X445
Fix dishwasher overfilling or not filling properly with a new float dome. Protects the float sensor for accurate water level control. Easy 15-minute repair.
Do-It-Yourself Stories from Customers like You
1 not draining properly 2 not cleaning properly 3 not filling properly 4 not running properly 5 sump and sump cap was filthy 6 James W. • San Diego , CA • March 19, 2017
1. Replaced the Dishwasher motor and pump assembly. 2. Replaced the lower arm sprayer. 3. Replaced the Sump and filter. Replaced both the inlet and outlet hoses. 4. Replaced the Airgap. 5. Replaced Float Dome. 6. Replaced Water Inlet Valve.
Parts $220 for Dishwasher
Estimated Labor $400.00
Labor $0.00
Parts $100.00 for Pullout Faucet
Estimated Labor $175.00
Labor $0.00
Read more
More
$15.52
- Compare At:
-
$18.62
- You Save:
-
$3.10