Kenmore Refrigerator 363.58272896 (36358272896, 363 58272896) Parts

Genuine Ge part

Refrigerator Drawer Slide Assembly (Left)

By: Ge

Part Number: WR72X252

This left-hand drawer slide assembly mounts inside the refrigerator's fresh food section. It supports the shelf/cover and guides the drawer on its track, restoring smooth operation and proper alignment when the original rail is cracked or worn.

Mounts on the left wall to support the shelf/cover and provide a smooth sliding track for the drawer
Keeps the drawer aligned and level for easy in-and-out movement
Replace when the existing rail is cracked, warped, or missing tabs
Typical symptoms: drawer hard to open/close, pops off track, shelf tilts or sags, visible damage to the rail

What's included: One left-side slide assembly Install notes:

Disconnect power and clear the compartment before starting
Remove the affected drawer and its shelf/cover to access the slide
Release locking tabs or remove mounting screws; transfer any reusable hardware to the new slide
Test drawer travel before reloading

Do-It-Yourself Stories from Customers like You My ice maker bin smelled like freezer burn and ice tasted like it too Nancy R. • New Paltz , NY • November 18, 2014

I bought whole new ice bin and it it's now the ice is great. Read more

Genuine Ge part

Snack Pan Slide Rail

5.0 (7)

By: Ge

Part Number: WR72X210

This replacement part is a snack pan slide rail, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. This part is able to hold up other trays and racks in the refrigerator and freezer so that extra shelf space can be utilized. These slide rails can also hold up trays that can support heavy bottles and drinks. A new snack pan slide rail might be needed if the current ones have become stripped and are unable to latch onto the shelving to support it. It is common that these parts can become brittle over time as exposure to low temperature wears down the plastic. Be sure the shelving of the appliance is clear before attempting to replace the slide rail. This is an OEM part sourced directly from the manufacturer. It is sold individually. This replacement part is compatible with different types of appliances made by General Electric.

Do-It-Yourself Stories from Customers like You Shelf in refrigerator needed to be replaced Daniel S. • Jacksonville , NC • September 29, 2018

Ordered parts from appliance parts pros and completed installation myself Read more

Genuine Ge part

Shield Lgt F

5.0 (5)

By: Ge

Part Number: WR17X3484

Do-It-Yourself Stories from Customers like You Original water value leak after 25 yrs of use Arthur J. • Greenville , FL • September 09, 2018

Replacing the valve assembly was just as easy as the video shows. I had an issue with the part I originally received due to damage in shipment. Contacted customer service whom were very professional. A replacement was shipped the same day and I received the part the next day. Thank you Appliancepartspro.com. Read more

Genuine Ge part

Ice Dispenser Deflector

5.0 (3)

By: Ge

Part Number: WR17X2059

This replacement part is an ice dispenser deflector, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice dispenser deflectors are found inside of the ice-making assembly and are an important part of many freezers. The ice dispenser deflector allows the ice to come down from the tray into the dispensing area. A new ice dispenser deflector might be needed if the current one has become too brittle and has even cracked or broken. Be sure that the refrigerator is completely powered off before starting this repair. The user must have access to the ice maker assembly and will need common household tools like a screwdriver and pliers. The user might also need working gloves as some parts in and around the assembly have sharp edges or blades.Note that this part is sold individually. This ice dispenser deflector is sourced directly from the manufacturer and is a genuine OEM replacement part.

Do-It-Yourself Stories from Customers like You The deflector broke John J. • Lexington , TN • April 22, 2014

Replaced the deflector Read more

Genuine Ge part

Slide Assembly Right

5.0 (5)

By: Ge

Part Number: WR72X253

Do-It-Yourself Stories from Customers like You Slide assembly left and right both were broken. Robert L. • Daytona Beach , FL • November 12, 2017

Ordered the parts and in a couple of days they arrived. A simple Philips screw driver was all that was needed to complete the install. Very simple, not complicated. You don't need to order the slide bushings as the slide assy. has them installed from the factory. Appliance Parts Pros is the best!!! terry,florida Read more

Genuine Ge part

Ring Compression

4.5 (2)

By: Ge

Part Number: WR02X10323

Do-It-Yourself Stories from Customers like You Refrigerator and freezer not cooling. Eric O. • Long Beach , CA • August 07, 2017

This is in a 15 year old Built-in Monogram that had the compressor replaced a few years ago. Before discovering the motor failure I replaced the main board since a Refrigeration Contractor I know said that if it wasn't bad it would be soon since those parts typically only last around eight years. The motor replacement is pretty simple; more time is spent getting to the motor and re-assembling everything than actually changing the motor. The trickiest part is getting the fan set correctly on... Read more

Genuine Ge part

Water Line Sleeve

5.0 (3)

By: Ge

Part Number: WR2X8933

Do-It-Yourself Stories from Customers like You Clogged drain tube Keith P. • Ivoryton , CT • March 03, 2017

Swapped it out for new tube. Take 5 minutes and zero effort. The drain tube will clog with mold. You can clean it out but the tube will clog again despite's you best efforts as the tube wall provide a great habitat. Ordered new tubes to facilitate swap-outs. Old tubes can be cleaned but will recolonize quickly. Read more

Genuine Ge part

Blade Condenser Fan Assembly

5.0 (3)

By: Ge

Part Number: WR60X10030

Do-It-Yourself Stories from Customers like You Condensor fan broke Chris R. • Rio Rancho , NM • November 28, 2016

Pulled out broken one and put on new one. Read more

Genuine Ge part

Pan Slide

5.0 (6)

By: Ge

Part Number: WR72X211

Left side.

Do-It-Yourself Stories from Customers like You Shelf in refrigerator needed to be replaced Daniel S. • Jacksonville , NC • September 29, 2018

Ordered parts from appliance parts pros and completed installation myself Read more

Genuine Ge part

Terminal Housing

By: Ge

Part Number: WH12X497

Harness to corset & shifter

Genuine Ge part

Bracket Evaporator Fan Sm.

5.0 (2)

By: Ge

Part Number: WR02X10100

Do-It-Yourself Stories from Customers like You The fan was not working. Donald B. • Laurens , SC • December 17, 2022

I replaced the Evaporator Fan Motor the brackets were rusty so I ordered them. Read more

Genuine Ge part

Ice Auger Blade

5.0 (2)

By: Ge

Part Number: WR2X7783

This replacement part is an ice auger blade, and it is intended for use in different types of appliances. This is a genuine replacement part made by General Electric. Ice auger blades are usually found in ice maker assemblies and are used during the ice-making and dispensing process. These blades are what are used when the user is in need of shaved or crushed ice. The mechanism takes full ice cubes and cuts the ice cubes down to create the different types of ice. A new ice auger blade might be needed if the user noticed that the current blades are dull or unable to cut ice. It is possible that the blades become dull over time after many years of use, so replacing them might be a good idea. Be sure the power is completely off before attempting to repair this part.This ice auger blade is sourced directly from the manufacturer and is a genuine OEM replacement part. Note that this part is sold individually.

Do-It-Yourself Stories from Customers like You Ice crusher repair GE Monogram counter depth. Glenn J. • El Cajon , CA • July 27, 2020

This was a very easy repair, the on-line video at AppliancePartsPros.com was helpful. The Helix was spinning freely (meaning, the Auger Blade was not holding it in place on the Auger). Pulling the assembly apart was a snap, and very logical (the video is perfect if you get lost). The family is now enjoying both crushed and cubed ice - and the redesign of the Auger Blade seems to prevent clogging in the ice shoot. Read more