Kenmore Refrigerator 363.9527810 (3639527810, 363 9527810) Parts

This breaker strip is the left-side trim piece that secures and seals freezer interior components, helping to maintain proper door fit and airflow. It replaces a worn or broken strip to restore a cleaner seal and finish. What it does:

• Provides a mounting/sealing surface along the left side of the freezer compartment to help hold liners and components in place
• Helps reduce gaps that can allow cold air loss or cause frost build-up when damaged
• Restores proper trim alignment and interior appearance
• Useful when the original strip is cracked, split, warped, or missing

• One left-side freezer breaker strip

• Inspect matching fasteners and mounting clips; replace any that are damaged
• Typical installation requires removing interior liners or trim pieces first — follow your model's service instructions
• Disconnect power to the appliance before performing interior repairs

This breaker strip is the wire terminal connector that secures and routes appliance wiring, restoring stable electrical connections and preventing loose or corroded contacts. It's a direct-fit service part used where multiple wires meet at a single terminal. What it does:

• Provides a secure terminal point for connecting and routing wires to multiple components
• Maintains consistent electrical contact to prevent intermittent operation
• Helps reduce arcing or sparking at worn or loose connection points
• Keeps wiring organized and aligned for proper fit and insulation

• One breaker strip

• Disconnect power to the appliance before inspecting or replacing the part
• Verify wire routing and terminal positions; transfer wires one at a time to avoid mis-wiring
• Use basic hand tools; avoid over-tightening terminals to prevent damage
• If terminals or surrounding wiring show burn damage, replace damaged wiring.

This RCSS control wire harness connects the refrigerator control system to sensors and components, restoring reliable signal and power routing for proper operation. Designed to replace a damaged or worn harness for safer, consistent performance. What it does:

• Routes power and control signals between the RCSS control module and related components
• Helps restore intermittent or lost functions caused by frayed, broken, or corroded wiring
• Prevents shorts and poor connections that can cause sporadic operation or failures
• Maintains factory wiring routing and connector fit for correct system communication

• Intended for technicians or experienced DIYers; disconnect power at the breaker before starting
• Match connectors and wire colors to the original harness before removal to ensure correct installation
• Inspect nearby components and connectors for damage or corrosion while replacing the harness
• Do not attempt repairs with power connected; follow OEM service manual for step-by-step procedures

Replace your damaged or missing refrigerator door shelf bucket. This bottom display bucket installs in the door to hold items securely. Order now.

The Evaporator Fan Motor Kit is an OEM part compatible with GE refrigerators. It is a critical component responsible for circulating air and maintaining proper airflow within the refrigerator's evaporator system, ensuring efficient cooling and temperature regulation. It features a shaft that measures 3/8 of an inch and two right-side terminals. Notably, the motor no longer comes with harness wires, which must be obtained separately for installation.

Symptoms of a faulty evaporator fan motor include:

• Inconsistent or inadequate cooling in the refrigerator or freezer compartments
• Warm spots or temperature fluctuations within the refrigerator
• Excessive frost buildup or ice accumulation in the freezer

Causes of a bad evaporator fan motor can include wear and tear over time, electrical issues or short circuits, or physical damage from foreign objects or improper maintenance.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore refrigerator models. 

The left Drawer Rail Slide is an OEM part for GE refrigerators. It provides smooth sliding action for refrigerator drawers, ensuring easy access and optimal storage management. This component guides the drawer in and out, preventing misalignment and supporting the weight of the drawer and its contents.  It measures approximately 14 7/8 inches long.

Over time, the drawer rail slide can become worn or damaged, leading to issues with drawer movement. Common causes of a bad drawer rail slide include normal wear and tear from frequent use, damage from overloading the drawer, or physical impacts that cause misalignment or breakage.

Symptoms of a bad drawer rail slide include:

• Difficulty opening or closing the drawer
• Drawer not aligning properly
• Excessive noise when operating the drawer
• Drawer falling off the rails

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

Note: For matching right-hand side order WR72X208.

The Drawer Slide Assembly is an OEM part for GE refrigerators. It provides the mechanism that allows refrigerator drawers to slide in and out smoothly. This assembly includes the tracks and glides that support the drawer, ensuring it moves effortlessly while staying securely in place.

Causes of a bad drawer slide assembly can include wear and tear from frequent use, accumulation of dirt and debris in the tracks, or physical damage from overloading or mishandling the drawer.

Symptoms of a bad drawer slide assembly include:

• Difficulty opening or closing the drawer
• The drawer not staying in place
• Unusual noises when moving the drawer
• The drawer feeling loose or wobbly

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models.

With a length of 16 1/4 inches, it is structured to support the crisper drawer. This facilitates its smooth and effortless sliding in and out. For matching left-hand side order WR72X207.

The Crisper Drawer Slide is an OEM replacement part for GE refrigerators. It facilitates the smooth movement of the crisper drawer, ensuring easy access to fruits, vegetables, and other stored items. This is the right-hand side refrigerator crisper drawer slide. Approx. 14 7/8 inches long.

Symptoms of a bad Crisper Drawer Slide include:

• The crisper drawer sticking or jamming, making it difficult to open or close
• Visible wear or damage to the slide, affecting its smooth operation
• The drawer not aligning properly, leading to an insecure fit
• The inability to fully extend or retract the crisper drawer

Causes for a malfunctioning Crisper Drawer Slide can include wear and tear from regular use, the accumulation of debris obstructing the slide's path, or damage incurred from overloading the drawer.

This GE replacement part is also compatible with Hotpoint, RCA, and some Kenmore models. For matching left-hand side order WR72X209.

This small shim adjusts the alignment and gap spacing of your refrigerator door hinges. It ensures proper door alignment and helps maintain an even seal around the door perimeter. Use this part if your refrigerator door doesn't close properly, has uneven gaps, or if the door appears misaligned.