Kenmore Dryer 417.84092500 (41784092500, 417 84092500) Parts

Ceramic dryer heating element terminal block.

This control board is the refrigerator's main electronic control that manages temperature, diagnostics and component operation for reliable cooling performance. Replace a failed board to restore responsive controls and system coordination. What it does

• Receives and processes signals from the user interface and sensors to run fans, compressor and defrost cycles.
• Regulates temperature by commanding cooling components based on thermostat and sensor inputs.
• Enables display functions, status indicators and diagnostic/error reporting.
• Can stop key functions if the board fails, causing unresponsive controls, no display or irregular cooling.

• One control board

• Disconnect power at the wall before attempting any service to avoid shock or damage.
• Handle the board carefully and avoid static discharge; use ESD protection if available.
• Transfer any wire harnesses or mounting hardware from the old board and secure all connections firmly.
• After installation, restore power and run diagnostics or a short test cycle to confirm normal operation.

Replacement Stackit2 3.0 module (TAW) designed to restore the intended fit and function of the Stackit2 assembly in compatible appliances. Offers a like-for-like replacement to address wear, damage, or missing pieces. What it does

• Replaces a worn, cracked, or missing Stackit2 3.0 module to restore proper assembly fit.
• Helps eliminate rattling, misalignment, or instability caused by a damaged module.
• Restores the original mounting/stacking interface so the appliance components seat correctly.
• Useful when visual damage or loss is present at the Stackit2 connection point.

• One Stackit2 3.0 module (TAW) as pictured.

• Disconnect power to the appliance before attempting any repair.
• Inspect surrounding components for additional damage before installing the replacement.
• Install in the original orientation; secure any fasteners removed during disassembly.

This wiring clip secures a refrigerator's wire harness to the cabinet or components to prevent chafing and keep wires organized. It helps maintain safe routing and reduces strain on electrical connections. What it does

• Holds wiring harness in place to prevent rubbing against sharp edges or moving parts
• Keeps wires organized to reduce the risk of pinching or accidental disconnection
• Helps prevent intermittent electrical faults caused by loose or strained wiring
• Commonly used near compressor, fan, control box, or rear cabinet areas

• Install by snapping the clip onto the cabinet flange or component and routing the harness through the retainer
• Disconnect power before accessing electrical components or wiring
• Inspect surrounding wiring and insulation; replace any damaged wire or harness tape before reinstalling the clip

This replacement plug seals an unused opening on compatible appliances to help prevent moisture, dirt and pests from entering and to restore the original appearance and fit. It's a simple, low-cost part for routine repairs. What it does

• Seals an access hole or unused opening to help keep moisture and debris out
• Helps block pests and contaminants from entering the appliance cabinet
• Secures wiring or tubing routing where a protective cap is required
• Restores original fit and finish at the plug location

• One replacement plug

• Disconnect power to the appliance before beginning any work
• Remove the access panel or trim necessary to reach the plug location
• Press the plug into place; small hand tools may help for snug seating
• Inspect surrounding gaskets and panels for damage while installing

This mounting bracket secures internal components and assemblies to keep panels, drawers, or modules aligned and stable. Installing the correct bracket restores proper fit and prevents excess movement or noise. What it does:

• Anchors and supports adjacent parts to maintain alignment and structural stability
• Keeps panels, drawers, or modules from shifting or sagging during use
• Helps eliminate rattling, vibration, or misalignment symptoms caused by a missing or damaged bracket
• Provides a fixed mounting point for screws or fasteners used in the assembly

• Disconnect power to the appliance before starting any repair
• Use appropriate tools and hardware; retain any original fasteners unless replacement is specified
• Handle edges carefully—brackets can have sharp metal corners

This mounting bracket secures internal components in place to keep appliance parts aligned and stable during normal use. Replacing a damaged bracket restores proper fit and support for affected assemblies. What it does:

• Provides structural support for internal panels or assemblies to prevent shifting and noise
• Helps maintain proper alignment of moving parts to reduce wear
• Stops rattling or vibration caused by a broken or bent bracket
• Keeps connected components securely attached after repair or reassembly

• One mounting bracket

• Disconnect power and water before starting any repair
• Inspect surrounding fasteners and hardware; replace any stripped screws for a secure fit
• Use proper-size tools to avoid damage to mounting holes or nearby components