Kenmore Refrigerator 596.75239404 (59675239404, 596 75239404) Parts

• Fridge too warm
• Noisy

I determined that the motor that drives the damper valve that allows cold air into the refer was noisy. I ordered the replacement part from AppliancePartsPro.com. It arrived within 3 days and I changed the units out, which took about 10 minutes total. All is quiet with the refer now. Read more

Having never fixed a fridge before, I did a little research. The unit was not old & the cooling system was operating. Observing the frozen ice inside, I diagnosed it as the heat rod and/or it's thermostat as bad. I contacted ApplianceParts Pros, who assisted in confirming my theory. IMPORTANT NOTE: the sales advisor Joyce was truly an intelligent, knowledgable professional, NOT some "burger-order taker" usually encountered. This alone speaks VOLUMES. Subsequently, the parts arrived... Read more

The manual had instructions for pulling things apart, the flaps over the drawer tops and the clear plastic inserts in the shelf. Flaps--Easiest to work with when the shelf is out and upside down. Slide flaps to the side a little to release the axle pin on the flaps from the receptacle hole on the shelf frame. Clear plastic plates are held in with a plastic pin on the side of the shelf frame. Carefully pull the side off the shelf there away from the pin slot until the insert pops out.... Read more

I bought the listed condenser fan motor for my Maytag refrigerator. Access to the condenser fan is by removing sheet metal screws of bottom panel with 1/4 in. nut driver. Condenser fan is on left side of rear access area. Remove electrical connector by pressing-in connector release tab with thumb fingernail and pulling on connector. Remove three mounting screws with 5/16 nut driver. Work fan out to the right past the compressor. I used a pair of pliers, as a lever, behind the plastic fan blades... Read more

Ordered the new gasket from you - installed it and now my freezer is sealed i called to order the correct replacement and they were the very best at helping me !!!!! Read more

Replaced It With New One Read more

Touch up paint Read more

Took off the freezer door, took off the top hinge on the refrigerator door, replaced the handle, re-installed the top hinge and the freezer door. This is a two person job - one to remove the top hinge and replace the handle, while a second person holds the refrigerator door in place. Replacing the handle was easy. The most irritating part was figuring out what parts to order. The drawing of the refrigerator door (Drawing # 4) used to figure out what parts to order was not clear. I paid $8... Read more

Ordered and paid for two day shipping and received on time. Read more

I watched the video on how to replace the ice maker and the replaced it with zero problems. Excellent help in trouble shooting problem and installation video further assisted in ease of installation. Read more

• Freezer not defrosting

My unit has a bottom freezer that is a drawer. I had to remove the drawer, rack, glides, glide tracks, and ice maker to remove the rear panel. This was a little difficult but after researching a few videos on line I learned some tricks that made it easier. I used a hair dryer to melt the ice. This is best done with 2 people having one at the back to sponge the water into a bowl from the pan to avoid a water mess. Using a bolt meter I checked the heating element and found it had continuity. I... Read more

My son broke the bottom shelf on the refrigerator door. I found the model number inside the frig and within 5 mins the part was on it's way! Ordered it Saturday morning , and arrived on Monday! Too easy! Slipped right into place! Read more

Replaced the gasket . Parts were were here one day after ordered . U-tube video was a big help. Went faster and easier than expected . Read more

• Leaking

I have a Whirlpool Side-by-side Model ED22PWXBW01. A year ago, the ice cubes started freezing together in the rear of the ice bin for no apparent reason. Although the problem started off small, it gradually grew much worse, and finally I could see water dripping out of the ice mold and into the bin during the fill cycle. Re-levelling the refrig didn’t help, nor did adjusting the cube size / fill level. With guidance from the video, I removed the icemaker from the wall of the freezer. The... Read more

Had to take the back cover off. It was very tight to remove the fan that sat in the drip pan but did get it off, was able to apply the same level of cursing and got the new pan installed, installing the drain tube was a breeze. Found the parts price very reasonable. Hoping the Whirlpool redesigned the pan so I won't have to do it ever again. I was surprised at how bad the quality of their original part was. Probably saved myself $150.00 on buying the part and doing it myself Read more

Replaced the ice level arm Read more