Kenmore Refrigerator 596.75504400 (59675504400, 596 75504400) Parts

Replace your refrigerator freezer door gasket to restore the seal and prevent frost buildup. Installs in minutes—press into door liner. Confirm fit by model.

The mullion rail is the vertical divider strip that separates the fresh food and freezer compartments in side-by-side refrigerators, often housing the water and ice dispenser controls. This part needs replacement if you notice cracks in the plastic, damaged dispenser components, or poor sealing between compartments that affects temperature control.

Replacement power cord for refrigerators. Restores electrical connection when the original cord is frayed, damaged, cracked, or has broken prongs.

Control knob broken, cracked, or won't turn? This replacement knob restores precise temperature and setting adjustments. Clips into place in minutes.

This support bracket holds your refrigerator's pantry drawer in the proper position for smooth operation. It prevents the drawer from sagging and ensures proper alignment with door seals. Replace if your pantry drawer won't slide smoothly or appears to hang unevenly.

Condensate drain pan collects water under your refrigerator. Replace if cracked, leaking, or damaged to prevent floor water pooling and spillage.

This thermostat retainer clip secures the defrost thermostat to the evaporator tubing in your refrigerator or freezer, maintaining firm contact for accurate temperature sensing and dependable defrost operation.

• Holds the thermostat firmly against the evaporator line for proper temperature feedback
• Helps prevent a loose or dangling thermostat that contribute to frost buildup and poor defrost performance
• Restores correct mounting when the original clip is cracked, bent, or missing
• Common signs include a broken clip or a thermostat not attached to the coil

• Disconnect power to the appliance before servicing; wear cut-resistant gloves
• Access the evaporator compartment; remove accumulated frost/ice as needed without prying on coil fins
• Position the thermostat body flat against the tubing and snap the retainer over it, avoiding pinched wires or damaged fins
• Confirm a secure fit and proper wire routing before reassembling and restoring power

Ice cubes stuck in tray and won't eject? This ejector arm pushes ice from the mold into the bin. Simple snap-in install restores ice production.

This slide temperature control is the user-access interface that moves the thermostat connection to select dryer heat levels. It restores responsive, indexed temperature selection for standard slide-style dryer controls. What it does

• Moves the internal contact to select low/medium/high heat settings for the dryer
• Replaces worn or loose slider that causes inconsistent or stuck temperature selection
• Helps correct symptoms such as inability to change heat level, intermittent temperature changes, or a slider that feels loose or won't stay in position
• Works as the mechanical interface between the console knob/lever and the dryer's control assembly

• One slide temperature control (single slider assembly)

• High-level replacement for users comfortable removing control consoles; disconnect power before service
• Handle control panel clips and trim carefully to avoid cracking plastic bezels
• Verify proper seating and alignment of the slider on the control shaft before reassembly

This temperature control bar is the actuator used to adjust and regulate the appliance's internal temperature, restoring proper temperature response for the bar/beverage control system. It provides a direct replacement for the OEM control bar assembly. What it does:

• Transfers user temperature adjustments to the control mechanism so the appliance reaches the set temperature
• Restores correct temperature changes when the control knob or selector fails to respond
• Helps address symptoms like incorrect temperature readings, temperature not changing, or unstable cooling behavior
• Works with the existing control housing and selector components to re-establish normal operation

• One temperature control bar

• Disconnect power before servicing to avoid electric shock
• Handle the part and surrounding components carefully to avoid damaging clips or wiring
• You may need to remove interior panels or the control housing to access the part;
• Verify the part number on your existing component before installation

Color: White

Note: For Black, order WP67002721. For Grey, order W11245157. 

A replacement handle release card that secures and releases a door handle assembly so the handle operates smoothly. Restores proper latch action and helps prevent a loose or stuck handle. What it does:

• Acts as the latch/retainer that locks the handle in place and lets it release when operated
• Replaces a worn or broken release card that can cause the handle to not engage or stick
• Helps stop excessive handle play and improves feel when opening or closing the door
• Compatible with the factory door/handle assembly it was designed to work with

• One handle release card

• Disconnect power or unplug the appliance before starting any repair
• Access may require removing the door trim or handle screws—retain fasteners for reassembly
• Inspect surrounding handle parts and replace any damaged clips or screws for best results

Black plastic corner cover replaces damaged or missing exterior trim on your refrigerator. Restores finished appearance and protects edges from wear.

Black plastic plug that seals unused refrigerator vent openings. Replace if yours is cracked, broken, missing, or damaged to keep out debris.

Replacement hinge bushing that cushions and supports refrigerator door hinges. Install when original is cracked, worn, or missing to restore alignment.

Replaces the small bumper that cushions your refrigerator door's travel. Needed when original is cracked, broken, or missing, causing hard impacts or slamming.