Kenmore Compactor 665.1340591 (6651340591, 665 1340591) Parts

Almond. Size: 13 oz. can. Acrylic appliance paint.

This switch nut secures a rotary control or switch to the appliance's front panel. Replacing a stripped or missing nut keeps the control stable so the knob turns smoothly and the shaft stays properly aligned.

• Clamps the switch/control to the panel to prevent movement or rotation
• Helps maintain correct knob alignment with dial markings
• Common symptoms: loose or wobbly knob, switch rotates in the panel, missing/damaged nut
• Often needed after service if the original nut is stripped or lost

• Disconnect electrical power before servicing
• Remove the knob and any decorative escutcheon; thread the new nut onto the switch bushing from the front of the panel
• Support the switch from behind while tightening; do not overtighten to avoid panel or switch damage
• Restore power and test control operation

This replacement stud is a factory-specified piece of hardware used to secure components in your appliance. Replacing a worn, stripped, or missing stud restores a solid fit to help reduce looseness and vibration. What it does:

• Provides a mounting point to fasten specified parts or panels
• Helps keep components aligned and secure during operation
• Replaces damaged, corroded, or missing original hardware
• Can resolve symptoms like loose parts, rattling, or misalignment where this fastener is used

• 1 stud

• Disconnect power; shut off water and/or gas supply if applicable
• Access the mounting location per your model's service information
• Start threads by hand to avoid cross-threading; tighten only until snug
• Reuse any original washers, clips, or nuts if required and in good condition

Color: Almond

This Inner Door Panel forms the interior surface of the dishwasher door. Replacing a dented or corroded panel restores proper sealing and structural support for the latch and dispenser, helping prevent leaks and rattling during wash cycles.

• Creates the interior door surface and directs water back into the tub
• Provides mounting points for the detergent/rinse aid dispenser, door latch, and vent components
• Helps maintain a watertight seal when the door is closed
• Replace if rusted, cracked, warped, or if dispenser/latch mounts are broken; may show leaks at the door or unusual rattling

• Disconnect power and water supply before servicing
• Open the door and remove perimeter screws; support the outer door panel as you separate the panels
• Transfer the dispenser, latch, vent, and any insulation/gaskets from the old panel to the new panel
• Reassemble with even screw torque; verify door closes/seals and run a short test cycle to check for leaks

This bearing supports a rotating shaft or assembly inside the appliance, reducing friction for smooth, quiet motion. Replacing a worn bearing helps eliminate noise, restore proper alignment, and prevent damage to mating parts.

• Supports and centers a rotating shaft or hub
• Reduces friction and wear for smoother, quieter operation
• Helps maintain alignment of connected components
• Common failure symptoms: grinding or squealing sounds, vibration or wobble, rough/stiff or seized rotation, excessive play

• Disconnect power before servicing; shut off water or gas if applicable
• Note orientation and retaining hardware before removal
• Use proper tools (puller/press) to remove and seat the bearing squarely—avoid hammering
• Inspect shaft/bore and related seals or spacers; replace worn components before reassembly

Size: 3\8-24 inch.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

A replacement screw used to secure the appliance power connection for reliable electrical contact and safe operation. Restores a solid connection if the original screw is missing, loose, or damaged. What it does:

• Secures the power terminal/cord or related power assembly to maintain consistent electrical contact.
• Helps prevent intermittent power, arcing, or overheating caused by loose or damaged fasteners.
• Replaces a missing, stripped, or corroded screw so the appliance can operate safely and reliably.

• Always disconnect power to the appliance before starting any repair.
• Use the correct screwdriver and thread engagement; avoid overtightening to prevent stripped threads or damaged terminals.
• Inspect adjacent wiring, terminals, and the cord strain relief; replace any damaged components.

Power screw hub is a replacement drive hub that secures the washer's drive screw/agitator to the transmission, helping restore proper agitation and reduce slipping. Fits applications where a worn or broken hub causes drive loss. What it does:

• Transfers rotational force from the drive screw/agitator to the transmission so the washer can agitate or spin.
• Replaces stripped or worn splines that allow the agitator or drive screw to slip under load.
• Common symptoms it can help fix: agitator or drum won't engage, intermittent agitation, grinding or squeaking during cycles.
• Install replacement if splines are visibly damaged or if the hub no longer holds the drive assembly securely.

• Disconnect electrical power (and water supply if applicable) before beginning any repair.
• Remove agitator/drive components; use the correct tools to avoid further spline damage.
• Inspect mating splines and fasteners; replace any damaged hardware and clean the area before installation.
• After reassembly, run a short test cycle to confirm normal operation.

This is the left side frame slide. For right side use W11722978.

Bottle with brush. Color: Platinum. Size: 0.6 fl.oz.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing

This mount plate is a stamped metal bracket that secures a component inside the appliance, helping keep parts aligned and reducing movement. Replace a damaged or bent plate to restore a stable, secure installation. What it does:

• Provides a stable mounting point for internal components to prevent shifting or sagging
• Helps reduce vibration and rattling caused by loose or worn mounting surfaces
• Keeps electrical and mechanical parts properly aligned for reliable operation
• Common symptom: visible looseness, noise, or component movement during use

• Disconnect power and unplug the appliance before starting any repair
• Verify the plate orientation and mounting hole alignment with your appliance's service diagram
• Use the original screws or OEM-specified fasteners and tighten securely but do not overtighten

This slide-ram is a replacement drawer slide component that restores smooth opening and reliable support for a freezer or refrigerator drawer. It helps the drawer track properly and reduces binding or sticking during use. What it does:

• Guides and supports the drawer as it opens and closes
• Replaces worn, cracked, or damaged slide hardware that causes sticking or uneven movement
• Helps realign a sagging or mis-tracking drawer for smoother operation
• Works as a direct-fit replacement where specified by the OEM

• Basic hand tools required; disconnect power and empty the drawer before starting
• Handle sharp edges carefully and keep small fasteners secure during reassembly
• If clips or screws are corroded or damaged, replace them with OEM-recommended fasteners

Bag carrier handle assembly that secures a disposable dust bag to the vacuum housing, letting you remove and replace bags cleanly and safely. Restores proper bag seating and handling for bagged vacuum units. What it does:

• Holds the dust bag in place so debris is directed into the bag, not the housing
• Provides a grip for removing and carrying full bags without tearing or spillage
• Replaces a cracked, broken, loose, or missing handle that prevents proper bag seating
• Helps stop bag detachment or leaks caused by an unstable carrier

• Always unplug the appliance before servicing.
• Remove the old bag and carrier, noting orientation; the carrier may snap into place or be secured with small screws.
• Verify the new carrier seats and latches fully before installing a new bag.