Kenmore Compactor 665.1340592 (6651340592, 665 1340592) Parts

Size: 6-32 x 3/8 inch.

Slotted pin spring secures moving parts in trash compactor assemblies. Replace if worn, missing, or damaged to restore proper retention and alignment.

Size: 8-32 x 1/4 inch.

This Inner Door Panel forms the interior surface of the dishwasher door. Replacing a dented or corroded panel restores proper sealing and structural support for the latch and dispenser, helping prevent leaks and rattling during wash cycles.

• Creates the interior door surface and directs water back into the tub
• Provides mounting points for the detergent/rinse aid dispenser, door latch, and vent components
• Helps maintain a watertight seal when the door is closed
• Replace if rusted, cracked, warped, or if dispenser/latch mounts are broken; may show leaks at the door or unusual rattling

• Disconnect power and water supply before servicing
• Open the door and remove perimeter screws; support the outer door panel as you separate the panels
• Transfer the dispenser, latch, vent, and any insulation/gaskets from the old panel to the new panel
• Reassemble with even screw torque; verify door closes/seals and run a short test cycle to check for leaks

A replacement screw used to secure the appliance power connection for reliable electrical contact and safe operation. Restores a solid connection if the original screw is missing, loose, or damaged. What it does:

• Secures the power terminal/cord or related power assembly to maintain consistent electrical contact.
• Helps prevent intermittent power, arcing, or overheating caused by loose or damaged fasteners.
• Replaces a missing, stripped, or corroded screw so the appliance can operate safely and reliably.

• Always disconnect power to the appliance before starting any repair.
• Use the correct screwdriver and thread engagement; avoid overtightening to prevent stripped threads or damaged terminals.
• Inspect adjacent wiring, terminals, and the cord strain relief; replace any damaged components.

Replacement drive hub that secures the compactor's power screw to the transmission. Needed when the original hub is worn, cracked, or broken.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing

0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.

Metal mounting bracket that secures internal components in your trash compactor. Replace if bent, damaged, or missing to restore stable part alignment.

Bag carrier handle assembly for trash compactors. Secures the disposable liner bag in place. Replace if cracked, broken, or missing to restore safe bag handling.

Rotary selector knob for compactor control panel. Snaps onto the control shaft. Replace if your original knob is cracked, broken, or missing.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Drive chain connects the motor to the ram mechanism in your trash compactor. Replace if the chain is broken, stretched, or missing to restore compaction function.

Touch up paint for appliances with chips, scratches, or worn spots. Includes brush applicator. Restores finish on damaged surfaces. 0.6 fl oz.