Kenmore Compactor 665.1358550 (6651358550, 665 1358550) Parts

Size: 8-32 x 1/4 inch.

Front guard plate for trash compactors. Protects the compactor front panel from damage. Replace if cracked, torn, or worn to restore appearance.

For use on power screw and ram pressure pads. Size: 4 oz. can.

This black refrigerator container handle replaces a worn, cracked, or missing pull on an interior bin or drawer. It restores a secure grip so you can easily slide the container in and out on compatible models.

• Attaches to the front of a refrigerator container or its cover to provide a solid handhold
• Replaces cracked, loose, or missing handle pieces
• Helps bins open and close smoothly without stressing the cover/front
• Common symptoms: handle broken or missing, tabs snapped, handle won't stay attached, drawer hard to pull

• Remove the bin/drawer and place the cover or front on a flat, protected surface
• Release the old handle by removing screws or disengaging tabs/clips (varies by model); keep hardware for reuse
• Align the new handle and snap or screw it into place; do not overtighten
• Handle glass and plastic parts carefully; wearing cut-resistant gloves is recommended

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing

0.6 oz. platinum touch-up paint with brush for appliances. Repairs scratches, chips, and gouges on doors, handles, and trim panels. Acrylic formula.

Metal mounting bracket that secures internal components in your trash compactor. Replace if bent, damaged, or missing to restore stable part alignment.

Bag carrier handle assembly for trash compactors. Secures the disposable liner bag in place. Replace if cracked, broken, or missing to restore safe bag handling.

Drive chain connects the motor to the ram mechanism in your trash compactor. Replace if the chain is broken, stretched, or missing to restore compaction function.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Fix excessive noise or wobbling components in your trash compactor with this wave washer retainer. Secures shaft-mounted parts to prevent movement.

Touch up paint for appliances with chips, scratches, or worn spots. Includes brush applicator. Restores finish on damaged surfaces. 0.6 fl oz.

Replacement power screw nut for trash compactors. Mounts on the drive screw mechanism. Order a new nut if yours is stripped, cracked, or worn out.

Touch-up paint for appliances in new avocado color. Covers chips, scratches, and worn spots on exterior surfaces. Includes brush applicator.

Latch spring for trash compactors. Installs in the door latch mechanism to provide tension. Replace if cracked, broken, or missing to restore proper latch function.