Kenmore Compactor 665.13612100 (66513612100, 665 13612100) Parts

This drive chain connects a washer's motor/transmission to the agitator or drum, transferring rotational motion so the wash basket spins and agitates properly. Replaces a worn or broken chain to restore normal drive function. What it does:

• Transfers motor torque to the transmission/agitator so the tub spins and agitates
• Commonly replaced when the washer won't agitate or spin despite motor running
• Replaces stretched, rusted, or broken chain that causes slipping or unusual noise
• Works as a direct mechanical link—no electrical components involved

• Install with the appliance unplugged and water supply turned off; follow OEM service manual for alignment and tension
• May require partial disassembly of cabinet, pulley, or transmission; have basic hand tools ready
• Inspect sprockets, tensioners, and related components and replace if excessively worn

This wave washer is a small, wavy metal retainer that holds rotating or sliding components in place on a shaft. It helps maintain proper alignment and reduces end-play for smoother, quieter operation. What it does:

• Secures components on a shaft to prevent axial movement and maintain alignment
• Helps reduce vibration and rubbing that can cause noise or premature wear
• Commonly used behind agitator, cam, or bearing assemblies where axial retention is required
• Replace if the washer is deformed, cracked, or missing to restore correct component spacing

• Disconnect power before starting repairs
• Remove the affected assembly (agitator/shaft or other specified part) to access the washer
• Install the washer in the same orientation and position as the original; ensure it seats fully
• Inspect surrounding components (bushings, seals, bearings) and replace any worn parts to prevent repeat failure

This safety switch actuator engages the door/interlock switch so the appliance senses a closed, secure door and will run as intended. Replacing a worn actuator restores reliable door engagement and control-system signaling. What it does:

• Moves the door latch into position to trip the appliance's safety/interlock switch
• Ensures the control board senses a closed door so cycles can start or continue
• Common symptom: appliance won't start or stops when the door is shut or nudged
• Common symptom: door won't fully latch or feels loose when closing

• One safety switch actuator

• Disconnect power (and water if applicable) before starting any repair
• Remove exterior panels or door assembly as needed to access the actuator; keep fasteners organized
• Verify switch alignment with the actuator and test operation before reassembly
• Wear gloves and eye protection

This deodorant is a replacement refrigerator deodorizer that helps reduce common food and household odors inside the fresh-food compartment for a cleaner-smelling interior. Simple swap helps maintain a neutral-smelling refrigerator. What it does:

• Adsorbs and reduces odors in the refrigerator interior to help keep food-smelling fresher
• Fits into the refrigerator deodorizer holder or designated compartment
• Works passively—no power or batteries required
• Helps refresh interior air between routine cleaning cycles

• For best results, remove old deodorizer and place new cartridge in the designated holder
• Disconnect power before beginning
• Wash hands after handling and follow local disposal guidelines for used cartridges
• If odors persist, inspect seals, drains, and spoiled food before replacing the deodorizer

Size: 6-32 x 3/8 inch.

This C-shaped retaining ring snaps into a groove on a shaft or pin to hold a component in place. It restores secure retention so parts don't slide off or shift during operation.

• Snaps into a groove to secure parts on a shaft or pin
• Prevents axial movement to keep assemblies aligned
• Helps reduce wobble, rattling, or parts migrating off
• Common signs: missing/broken clip, loose mechanisms, parts slipping off during use

• Disconnect power; also shut off water or gas as applicable
• Wear eye protection—retaining clips can spring free during removal/installation
• Use appropriate snap/retaining ring pliers or a small flat tool; avoid over-expanding the ring
• Ensure the ring seats fully in the groove and replace if bent or fatigued

A small slotted pin spring used to secure moving parts in appliance assemblies. This compact replacement restores proper retention and alignment where a slotted spring pin is required, helping moving parts stay in place and operate smoothly. What it does:

• Acts as a slotted spring pin to hold shafts, levers or clips in position
• Restores secure retention when original pin is bent, worn or missing
• Prevents excess play or disengagement of connected components
• Helps resolve symptoms like loose or shifting parts, rattling, or components not staying engaged

• One slotted pin spring

• High-level replacement; retains existing mating hardware and holes
• Use proper tools (needle-nose pliers, punches) to remove/install without damaging surrounding parts
• Wear eye protection; pins can release under tension during removal

This is a replacement screw used to secure appliance panels and components. It restores proper fit and prevents loose parts that cause vibration, rattling, or misalignment for a tighter, safer assembly. What it does:

• Secures covers, trim, brackets, or control panels to the appliance frame
• Keeps components aligned to prevent rattling and movement during operation
• Replaces stripped, missing, or damaged fasteners that compromise fit
• Helps restore structural stability for normal operation

• Disconnect power and turn off water supply before beginning any repair
• Use the correct screwdriver or driver bit to avoid stripping the head
• Hand-start the screw and tighten until snug; avoid over-tightening which can crack plastic or strip threads
• If threads are damaged, replace with correct OEM fastener.

Size: 8-32 x .312 inch.

This flat metal washer provides a durable spacer and load-bearing surface for fasteners in the appliance, helping maintain proper alignment and reduce wear on mating parts. It's a simple replacement that restores correct assembly spacing. What it does:

• Acts as a load-distributing spacer between fastened components to prevent loosening and wear
• Helps maintain proper alignment of shafts, housings, or assemblies
• Can reduce vibration or movement caused by uneven mating surfaces
• Commonly replaced when hardware is corroded, damaged, or missing

• One flat metal washer (quantity: 1)

• Verify the exact washer size and thickness before installation; replace with the same type
• Tighten fasteners to the manufacturer's torque specifications when known; avoid overtightening
• If used near electrical connections, ensure power is disconnected before working
• Inspect adjacent fasteners and components for wear and replace if necessary

The Drive Gear Kit is an OEM replacement part for Whirlpool trash compactors. It is an essential component that powers the compaction mechanism. The drive gear kit consists of a series of gears, shafts, and other components that work together to transfer the motor's rotational force to the compaction ram.

Causes of a bad drive gear kit in a trash compactor can include mechanical wear and tear over time, exposure to excessive loads or foreign objects, or damage from improper usage or maintenance.

Symptoms of a faulty drive gear kit in a trash compactor:

• Difficulty in starting or completing the compaction cycle
• Loud grinding or squeaking noises during operation
• Failure of the compaction ram to move or compress waste properly
• Leaks or vibrations due to improper alignment or gear damage

This OEM part is also compatible with Maytag, KitchenAid, Jenn-Air, Amana, Magic Chef, Admiral, Norge, Roper, and Kenmore trash compactor models.

This door lock latch assembly secures the washer door during operation so cycles can run safely and water stays contained. It replaces a worn or damaged latch to restore proper door locking and cycle start. What it does

• Secures and locks the washer door during wash and spin cycles so the appliance can operate normally.
• Triggers the door-closed sensor/switch that allows the washer to start and continue a cycle.
• Helps prevent accidental door opening and reduces the risk of leaks during operation.
• Common symptoms indicating this part may be needed: washer won't start, door won't latch or lock, or the latch feels loose or broken.

• Always disconnect power to the appliance before inspecting or replacing the door lock latch.
• Handle the door and glass carefully to avoid damage; align the latch with the strike before tightening fasteners.
• After installation, test a short cycle (no clothes) to ensure the door locks and the washer starts properly.

This bracket kit secures and supports internal appliance components to keep panels and assemblies aligned for reliable operation. It replaces worn or damaged brackets so parts stay firmly in place and reduce movement or noise. What it does:

• Provides a mounting point to secure panels, assemblies or components
• Restores proper alignment and prevents shifting during operation
• Reduces rattling, vibration, and loose or sagging panels
• Helps maintain safe, stable function of the related assembly

• Turn off power and unplug the appliance before starting any repair
• Use basic hand tools; follow model-specific disassembly steps
• Keep fasteners and small parts organized during removal and reassembly

Bottle with brush. Color: Platinum. Size: 0.6 fl.oz.

This replacement leveling wheel restores a dryer/washer cabinet's ability to sit level and roll smoothly during adjustment. It helps stop wobble and ensures the appliance can be properly leveled for stable operation. What it does:

• Replaces a worn or broken leveling wheel on the appliance base or leveling assembly
• Allows the cabinet to be adjusted up or down when setting appliance height
• Helps reduce rocking, uneven vibration, and unstable operation caused by a damaged leveler
• Works with the appliance's leveling hardware to keep the cabinet properly supported

• One replacement leveling wheel

• Disconnect power and water before beginning any work
• Support the appliance securely to relieve weight from the leveling assembly before removal
• Remove the old wheel from the leveler shaft and press or snap the new wheel into place; use basic hand tools as needed