Kenmore Dishwasher 665.13739K604 (66513739K604, 665 13739K604) Parts

This inner door plastic is the interior panel for the appliance door that supports latch and hinge hardware and helps maintain the door seal. Replacing a cracked or damaged inner panel restores proper door fit and function. What it does:

• Supports the door assembly and secures internal components; a damaged panel often causes a loose or rattling door.
• Provides mounting points for the latch and hinge hardware; symptoms include a door that won't latch or closes unevenly.
• Helps maintain the appliance seal and thermal integrity; symptoms can include noticeable air/heat leakage or reduced performance.
• Restores the interior appearance of the door when the original plastic is cracked, warped, or broken.

• Disconnect power to the appliance before beginning work and fully open the door; support the door to prevent it from dropping when fasteners are removed.
• Remove the required screws/fasteners and lift out the inner panel carefully; wear safety gloves and eye protection if glass is present.
• Check hinge and latch alignment during reassembly; replace any damaged fasteners and avoid overtightening screws which can crack the plastic.

Secures ground wire to dishwasher chassis for safe electrical connection. Replace if clip is damaged, missing, or fails to hold wire firmly. Verify fit.

Controls water level and prevents overfilling in your dishwasher. Replace if you notice leaking or overflow issues. Confirm fit using your model number.

Replacement clip that secures the dispenser guard on compatible Whirlpool refrigerators. Replacing a damaged or missing clip restores a secure dispenser trim and can reduce rattling or misalignment around the dispenser area. What it does:

• Secures the dispenser guard/trim to the dispenser assembly to keep the trim aligned.
• Commonly needed when the guard is loose, rattling, cracked or falls out.
• Replaces broken or missing clips that allow the dispenser trim to move or vibrate.
• Helps restore proper fit of the dispenser trim so the dispenser components sit flush.

• Disconnect power (unplug or turn off the circuit) and shut off the water supply if working near the water/ice dispenser.
• Remove the dispenser trim or guard per the model's service instructions; handle plastic parts gently to avoid cracking.
• Align the clip with the mounting slot and engage until seated; if access is limited or the guard is damaged, follow safety guidelines when servicing appliances.

Fix dishwasher leaks or rattling from the sump area with this sump tab. Secures the sump assembly to the tub, preventing movement and water seepage.

Pronged cup washer for securing internal dishwasher components. Provides reliable retaining force for assembly hardware.

Dishwasher overfilling or flooding? This overfill switch stops the fill cycle when water reaches unsafe levels. Easy DIY fix for water control issues.

13 oz. enamel spray paint in biscuit color for appliances. Restores scratched, chipped, or discolored surfaces on refrigerators, dishwashers, and more.

Size: 8-32 x 1/2 inch.

This dual BR2 positioner secures and aligns linked components so moving assemblies operate smoothly and reliably. Replaces a worn or broken positioner to restore correct part orientation and reduce misalignment-related issues. What it does:

• Holds and indexes two linked components to maintain correct alignment during cycles
• Helps prevent binding, noisy operation, or mis-positioned parts
• Restores proper mechanical engagement after breakage or wear
• Works as the mounting/locator piece that keeps assemblies in their intended position

• Disconnect power to the appliance before starting any repair
• Remove the appropriate access panels to reach the old positioner; keep fasteners organized
• Note wiring or linkage locations (take a photo) before removing the old part for proper reassembly
• Reinstall panels and restore power; test the appliance to verify correct operation

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

Replacement wheel leg assembly for dishwashers. Restores mobility and stable support when original leg is cracked, broken, or worn. Snaps into groove.

4-24 x 3/8 screw secures trim panels, brackets, and internal components in your dishwasher. Replace if missing, stripped, or corroded during repairs.

Replace your dishwasher's bag assembly to restore proper containment and collection function. Easy direct-fit swap for damaged or missing parts. Verify fit with your model number before ordering.

Fix a broken or missing dishwasher detergent dispenser cover. This shield protects the dispenser assembly and restores a finished look to your unit.

Covers and directs dishwasher exhaust while keeping the vent opening protected. Replace if cracked, discolored, or loose. Verify fit with your model number.