Kenmore Dishwasher 665.13739K604 (66513739K604, 665 13739K604) Parts

Shield for dishwashers. Protects internal components from water and debris. Replace if cracked, broken, or missing to maintain proper coverage.

This is a small plastic or rubber fitting that secures the power cord where it enters the dishwasher's junction box or base. It prevents the electrical wiring from being pulled, kinked, or damaged by absorbing tension on the cord. Replace this part if it is cracked or missing, which can leave wiring exposed and vulnerable to damage during installation or use.

Fix water leaking from under your dishwasher with this pump volute. Directs water flow and prevents leaks with integrated seal. 20-minute repair.

This replacement screw fastens appliance components such as panels, brackets, or trim. Use it to replace a missing, stripped, or rusty fastener and restore a secure, rattle-free fit in your appliance assemblies.

• Secures panels, brackets, or hardware to maintain proper alignment
• Helps eliminate vibration, rattling, or loose-feeling parts
• Replaces fasteners that are missing, corroded, or cross-threaded
• Typical signs you need it: loose handle or panel, gaps, or hardware that won't stay tight

• Disconnect power (and shut off gas, if applicable) before servicing
• Match thread type and length to the original fastener for proper fit
• Start threads by hand to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if present

Fix a dishwasher motor that hums or won't start. This run capacitor provides the phase shift needed for smooth motor operation. DIY repair in 30-45 min.

This is a rubber gasket that seals around the door vent opening on a dishwasher, preventing steam and moisture from escaping into areas where they can cause damage. It fits between the vent assembly and the inner door panel. Replace this gasket if you notice moisture or steam leaking from around the vent area, water dripping down the front of the door, or if the gasket appears cracked, warped, or deteriorated.

Replacement clip that secures the dispenser guard on compatible Whirlpool refrigerators. Replacing a damaged or missing clip restores a secure dispenser trim and can reduce rattling or misalignment around the dispenser area. What it does:

• Secures the dispenser guard/trim to the dispenser assembly to keep the trim aligned.
• Commonly needed when the guard is loose, rattling, cracked or falls out.
• Replaces broken or missing clips that allow the dispenser trim to move or vibrate.
• Helps restore proper fit of the dispenser trim so the dispenser components sit flush.

• Disconnect power (unplug or turn off the circuit) and shut off the water supply if working near the water/ice dispenser.
• Remove the dispenser trim or guard per the model's service instructions; handle plastic parts gently to avoid cracking.
• Align the clip with the mounting slot and engage until seated; if access is limited or the guard is damaged, follow safety guidelines when servicing appliances.

Internal rear feed cap for dishwasher spray arm system. Replace if damaged, cracked, or water leaks from the rear feed area. Confirm fit with your model.

This is the main circulation pump motor that pressurizes and circulates water through the spray arms during the wash and rinse cycles. It is mounted beneath the dishwasher tub and drives water through the wash system. Replace this motor if the dishwasher fills with water but does not spray, makes unusual humming or grinding noises during the wash cycle, or leaves dishes dirty.

This adjustable manifold is a direct-fit replacement that secures and positions the appliance's manifold assembly so related components line up and function correctly. It restores proper alignment and reliable operation when the original is bent or worn. What it does:

• Provides a mounting surface and adjustable position for the manifold assembly and attached components
• Helps maintain correct alignment so burners/valves operate smoothly
• Restores fit when the original manifold is damaged, bent, or loose
• Resolves symptoms such as uneven burner operation, ignition difficulty, or mechanical misalignment

• Turn off power and shut off gas supply before starting work
• Handle and align carefully to avoid bending; secure with the OEM fasteners
• Check seals and connections after installation; test operation per manufacturer instructions

Covers and directs dishwasher exhaust while keeping the vent opening protected. Replace if cracked, discolored, or loose. Verify fit with your model number.

White outer door panel for dishwashers. Replaces cracked, dented, discolored, or mismatched front panels. Updates appearance and covers damage.

Color: Biscuit. Screw for lower toe panel. For black screw use WP302868, for white screw use WP3400836.

Color: White. Size: 1 qt. can. Acrylic appliance paint.

Cosmetic panel that covers the space beneath your dishwasher. Replace if cracked, dented, discolored, or missing to restore a finished appearance.

Flat washer for dishwasher fasteners. Distributes load and prevents loosening at mounting points. Replace when worn or missing to reduce vibration. Confirm fit with your model number.