Kenmore Dishwasher 665.13962K013 (66513962K013, 665 13962K013) Parts

This stud is a small mounting fastener that provides a secure anchor point for attaching appliance components. Replacing a worn or missing stud restores a tight, aligned fit and helps prevent looseness, rattles, or shifting.

• Provides a fixed, threaded anchor for mounting a handle, bracket, or panel
• Helps keep parts aligned and secure during normal operation
• Common replacement for studs that are stripped, bent, broken, or missing
• Symptoms can include a loose or wobbly component, difficulty tightening, or visible damage/corrosion

• Disconnect power and, if applicable, shut off water or gas before servicing
• Wear cut-resistant gloves and handle panels carefully
• Hand-start threads to avoid cross-threading; tighten snugly without over-torquing
• Reinstall any covers or related hardware in their original positions

Dishwasher won't start, runs too long, or behaves erratically? The main control board coordinates all wash cycles. Moderately challenging repair.

Insulation pad that fits behind dishwasher panels to restore thermal protection and reduce noise. Replace if damaged, missing, or rattling occurs.

Replacement 8-32-thread screw used to secure panels, brackets and small components in compatible household appliances. Restores missing or stripped fasteners so panels and parts stay firmly attached during normal use. What it does:

• Secures trim, panels, brackets and control housings to maintain proper assembly.
• Replaces missing or damaged screws that can cause rattling, loose panels or misaligned components.
• Fits locations that require an 8-32 threaded fastener; correct length and head style for your application.
• Helps restore stable, vibration-free operation when worn or stripped fasteners are replaced.

• Disconnect power and water before servicing; wear eye protection and gloves.
• Use the correct screwdriver or driver bit to avoid stripping the screw head.
• Do not overtighten—turn until snug and secure to avoid damaging threads or surrounding parts.
• If the original used a washer or nut, reuse or replace as needed and the screw length and head type match the original.

This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.

• Provides adjustable support at one corner of the appliance
• Helps level the unit for correct alignment with floor or cabinetry
• Reduces rocking, vibration, and rattling noises
• Replaces stripped, bent, cracked, or missing leg

• Disconnect power and, if applicable, shut off water before servicing
• Carefully support or brace the appliance to access the base safely
• Start the new leg by hand to avoid cross-threading; adjust height gradually
• Use a level to check side-to-side and front-to-back, then recheck after positioning

10-32 thread machine screw secures panels, brackets, and internal components. Replace missing, stripped, or damaged fasteners to restore solid fit.

Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.

This manifold is the OEM gas valve assembly that routes propane or natural gas from the regulator to the oven and burner valves so the appliance can ignite and heat properly. Designed as a direct-replacement service part. What it does

• Channels gas from the regulator to individual burner/oven valves so each burner can ignite.
• Replaces a worn or damaged manifold that can cause weak or no ignition.
• Addresses symptoms such as burners that won't light, oven failing to heat, or inconsistent flame across burners.
• Works with the appliance's existing regulator and control valves when installed correctly.

• Turn off gas supply and electrical power before attempting removal or service.
• Inspect fittings and gaskets; replace any damaged seals to prevent leaks.
• After installation, perform a gas-leak test and verify proper ignition and flame patterns.

Secures trim and panels in dishwasher assemblies. Replace if clip is broken, missing, or worn. Prevents loose parts and rattling during operation.

Secures ground wire to dishwasher chassis for safe electrical connection. Replace if clip is damaged, missing, or fails to hold wire firmly. Verify fit.

Factory #10-16 screw secures dishwasher panels, brackets, and covers. Replace worn, stripped, or missing screws to restore tight assembly.

Pronged cup washer secures and cushions components in dishwashers and microwaves. Replace when worn to restore stable fit and reduce wobble.

10-24 threaded machine screw secures panels, brackets, and internal assemblies in appliances. Replace missing, stripped, or damaged screws.

Secures knobs, trim, or linkages to shafts inside your dishwasher. Replace if broken, cracked, or missing to prevent components from loosening.

Size: 8-32 x 1/2 inch.

13 oz. enamel spray paint in biscuit color for appliances. Restores scratched, chipped, or discolored surfaces on refrigerators, dishwashers, and more.