Kenmore Dishwasher 665.1569580 (6651569580, 665 1569580) Parts
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302868
Color: Black. Screw for lower toe panel. For Biscuit screw use 3400865, for white screw use WP3400836.
Do-It-Yourself Stories from Customers like You
Dishwasher door panel was rusting Prashant K. • Fishers , IN • October 11, 2014
I had no hope of separating the panel from the frame without damaging the frame since the two parts were rusted pretty badly and the screws holding the panel to the frame were completely beyond salvage. So I had to replace both the panel and the frame. I ended up removing the electrical/electronic connections, removing the panel/frame from the hinge and then replacing it with the new parts. Took about 90 minutes but the hardest part was removing other items from the rusting frame without...
Read more
More
$7.95
- Compare At:
-
$9.38
- You Save:
-
$1.43
Genuine Whirlpool part
By: Whirlpool
Part Number: 717000
This seal kit is for the main tub. It goes around the pump housing.
Do-It-Yourself Stories from Customers like You
Leaks from around the door and from the pump motor Samuel M. • Sudbury , MA • January 12, 2016
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed...
Read more
More
$37.95
- Compare At:
-
$45.16
- You Save:
-
$7.21
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302711
This pump outlet seal sits on the discharge side of the dishwasher pump to keep the outlet connection watertight. Replacing a worn seal helps stop leaks and keeps wash water contained during the cycle. What it does:
- Seals the joint at the pump outlet to prevent water leakage
- Helps maintain proper circulation by keeping the pump discharge airtight/watertight
- Common symptoms of failure include water under the unit, drips near the pump area, or a flattened/cracked/hardened old seal
What's included:
Install notes:
- Disconnect power and shut off the water supply before servicing
- Remove the toe-kick/lower access panel to reach the pump area; place a towel or pan to catch residual water
- Note seal orientation; clean mating surfaces before installing the new seal
- Seat the seal evenly; reassemble and run a short test to check for leaks
Do-It-Yourself Stories from Customers like You
Loud dishwasher producing dirty dishes Leon F. • Sylmar , CA • November 11, 2015
I nearly shelled out for a new Kitchenaid when I remembered APP and entered my model # just for fun. The interactive diagrams and install videos showed where all the parts "should" be, mine were badly disintegrated, so I replaced the damaged ones and swapped out all of the other easily accessible seals and bearings (also gave it a good and very disturbing cleaning). My parts surprisingly arrived next day and for about $40, the dishwasher is quiet and works like new again.
Read more
More
$24.95
- Compare At:
-
$29.94
- You Save:
-
$4.99
Genuine Whirlpool part
By: Whirlpool
Part Number: 4317824
The Power Cord Kit is an OEM replacement part for Whirlpool dishwashers. It is a 3-prong grounded, 16-gauge cord that includes all the hardware needed for installation. Includes all hardware needed for installation.
Causes of a bad power cord can include normal wear and tear over years of use, accidental impacts or cuts to the wiring, or improper installation that damages components.
Symptoms of a bad power cord include:
- The dishwasher not turning on or completing cycles
- Warm or hot power cords during operation
- Frayed, cracked, or exposed copper wiring
This is a genuine Whirlpool OEM replacement this part is also compatible with Maytag, Jenn-Air, and some Kenmore models.
Do-It-Yourself Stories from Customers like You
Mice chewed the drain hose and power cord Noah C. • Eastsound , WA • February 16, 2015
Read directions on how to change the power cord and watched video on your site on how to change the drain hose. Everything went perfectly.
Read more
More
$20.95
- Compare At:
-
$24.93
- You Save:
-
$3.98
Genuine Whirlpool part
By: Whirlpool
Part Number: WP9741232
Quantity of ONE.
Size: 8-18 x 5/8 inch.
(#8 screw, 18 threads per inch, 5/8 inch long)
Do-It-Yourself Stories from Customers like You
My dishwasher was leaking out copious amounts of water while cycling Michael K. • Oakland , MI • July 11, 2019
While at my sister's house, she showed me how to access & dismantle the housing unit on her dishwasher, thinking the issue might be from that area. So, when I came home, I opened up my housing unit and found that several of the screws had come out and the pump outlet seal was stretched out and partially outside of the unit itself. I located all of the missing screws & discovered I was still missing one, which my husband helped me order with the pump outlet seal. I easily replaced the old seal...
Read more
More
$7.95
- Compare At:
-
$9.54
- You Save:
-
$1.59
Genuine Whirlpool part
By: Whirlpool
Part Number: 4317933
This kit includes 4 double roller attachments. Enough for one lower rack. Color: white. Each roller attachment measures about 3 inches high by 6 inches deep.
Do-It-Yourself Stories from Customers like You
Broken roller on lower dishwasher basket Linda H. • Conyers , GA • July 25, 2014
Popped the old rollers off and snapped on new ones.
Read more
More
$28.95
- Compare At:
-
$34.45
- You Save:
-
$5.50
Genuine Whirlpool part
By: Whirlpool
Part Number: W11693756
This factory fastener is a #8-18 x 5/8-inch Type AB screw designed for appliance assembly. It secures panels and components to restore a tight, rattle-free fit and dependable alignment. What it does:
- Thread-forming Type AB design engages thin metal or plastic components
- Secures panels, brackets, trim, or covers to reduce looseness and vibration
- Replaces missing, stripped, or corroded fasteners
- Helps maintain alignment for proper operation and reduced noise
What's included:
Install notes:
- Disconnect power before servicing; shut off water supply if working near water lines
- Use the correct driver for the screw head; start by hand to avoid cross-threading
- Tighten until snug—do not overtighten to prevent stripping or cracking plastic
- Repair damaged holes or replace worn clips/inserts before installing the new screw
Specs:
- Size: #8-18 x 5/8 in (length 0.625 in)
- Thread type: Type AB, thread-forming
Do-It-Yourself Stories from Customers like You
Door switch on dryer. James A. • Middleburg , FL • January 20, 2020
It was very easy to fix after watching your video..
Read more
More
$10.95
- Compare At:
-
$12.92
- You Save:
-
$1.97
Genuine Whirlpool part
By: Whirlpool
Part Number: WP489069
Size: 1/4 inch hex head, 10-12 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
Broken handle foot pedal and missing parts Donald M. • Lake Arrowhead , CA • April 05, 2015
This trash compactor is in our vacation home. We never use it and now we are selling the house. When I looked to replace it I was amazed at how expensive a new compactor would cost. I found the serial number on the current compact entered it and your web site came up. Your schematics were excellent and made the repair very easy!
Read more
More
$5.95
- Compare At:
-
$7.02
- You Save:
-
$1.07
Genuine Whirlpool part
By: Whirlpool
Part Number: WP3367052
This hose clamp secures a flexible hose to its fitting to help prevent leaks and hose blow-offs during operation. Replace a rusted, stripped, or distorted clamp to restore a tight, reliable seal at the connection point.
- Applies clamping force around a hose to hold it on a barb or stub fitting
- Commonly used on washer drain and tub-to-pump hose connections
- Helps stop drips at the joint and prevents the hose from slipping off
- Typical failure signs: leaking at the connection, clamp won't tighten, visible rust, broken/warped band
What's included: 1 hose clamp Installation notes:
- Unplug the appliance and turn off water supply; expect some residual water
- Seat the hose fully on the fitting; place the clamp just behind the bead/barb
- Tighten until snug and secure; do not overtighten to avoid damaging the hose
- Run a short test cycle and recheck for leaks at the connection
Do-It-Yourself Stories from Customers like You
Fill hose leaking at crimp fitting by faucet connector faucet adapter leaking (whirlpool portable dishwasher) Ralph P. • San Antonio , TX • August 21, 2016
Replace faucet adapter, replace fill and drain hose assembly. You must remove outer cabinet to be able to route new hoses and access hose connections under tub.
Read more
More
$5.95
- Compare At:
-
$7.14
- You Save:
-
$1.19
Genuine Whirlpool part
By: Whirlpool
Part Number: WP302710
This inlet base seal is a gasket that fits between the inlet base and its mating surface. Replacing a worn seal helps maintain proper airflow through the inlet path and keeps spills and debris out of internal components.
- Forms a tight, continuous seal at the inlet base-to-housing joint
- Helps preserve correct airflow through the inlet path
- Blocks liquids, grease, and crumbs from leaking into the appliance interior
- Replace if the seal is cracked, flattened, brittle, loose, or you see visible gaps
What's included: One inlet base seal.
- Disconnect power to the appliance before servicing
- Remove grates/cartridges, filters, or trim as needed to access the inlet base
- Clean and dry mating surfaces; install the new seal in the same orientation without stretching or twisting
- Reassemble and verify the seal sits evenly with no gaps
Do-It-Yourself Stories from Customers like You
Leaks from around the door and from the pump motor Samuel M. • Sudbury , MA • January 12, 2016
1. To fix the leaks from around the door, I replaced the upper and lower door seals. These were purchased in a separate transcation, so they are not the parts shown here. The upper door seal worked as intended, but the lower seal would not stay in place on the lower edge of the door during a wash. Therefore I cleaned the grease and detergent off the old seal, and installed using silicone sealer/adhesive. The plastic edge pieces for the lower seal were supplied with the kit, and they installed...
Read more
More
$6.63
- Compare At:
-
$7.89
- You Save:
-
$1.26
Genuine Whirlpool part
By: Whirlpool
Part Number: WP488627
This flat-head screw secures panels, brackets, or trim so they sit flush on your appliance. Replacing a worn or missing screw restores a tight fit and helps prevent vibration, rattling, or shifting components.
- Provides a countersunk, flush-mount fastener for panels, trim, brackets, or covers
- Helps maintain alignment and secure attachment during operation
- Replaces stripped, rusted, or missing hardware
- Symptoms can include loose panels or handles, rattling noises, or visible gaps/misalignment
What's included: 1 flat-head screw Install notes:
- Disconnect power (and shut off gas, if applicable) before servicing
- Match screw length and thread to the original for proper fit
- Start threads by hand to avoid cross-threading; tighten snugly without overtightening
- Support the part being fastened to keep alignment while tightening
More
$12.95
- Compare At:
-
$14.57
- You Save:
-
$1.62
Genuine Whirlpool part
By: Whirlpool
Part Number: 350956
Almond. Size: 13 oz. can. Acrylic appliance paint.
Do-It-Yourself Stories from Customers like You
Age no money to fix it Ronald V. • Cape Coral , FL • August 01, 2015
Was able to match it pretty well the natural age difference was good. The delivery of the product was amazing it took less than 24 hours to get to me and that was standard shipping. Give you guys an A for great !!
Read more
More
$30.52
- Compare At:
-
$36.32
- You Save:
-
$5.80
Genuine Whirlpool part
By: Whirlpool
Part Number: WP72107
Color: Almond
Do-It-Yourself Stories from Customers like You
Broken meat drawer Jesse B. • Stow , MA • January 26, 2015
Replaced. Shippping was very fast. A good experience.
Read more
More
$14.95
- Compare At:
-
$17.79
- You Save:
-
$2.84
Genuine Whirlpool part
By: Whirlpool
Part Number: 8193716
This adjustable leveling leg threads into the appliance base to set height and stabilize the cabinet. Replacing a worn or missing leg helps stop rocking and vibration and helps maintain proper alignment for reliable operation.
- Provides adjustable support at one corner of the appliance
- Helps level the unit for correct alignment with floor or cabinetry
- Reduces rocking, vibration, and rattling noises
- Replaces stripped, bent, cracked, or missing leg
What's included: 1 adjustable leveling leg Install notes:
- Disconnect power and, if applicable, shut off water before servicing
- Carefully support or brace the appliance to access the base safely
- Start the new leg by hand to avoid cross-threading; adjust height gradually
- Use a level to check side-to-side and front-to-back, then recheck after positioning
More
$43.95
- Compare At:
-
$52.30
- You Save:
-
$8.35
Genuine Whirlpool part
By: Whirlpool
Part Number: 285006
Color: Black. Size: 12 oz. Acrylic appliance aerosol can spray paint.
Do-It-Yourself Stories from Customers like You
My 1984 dishwasher that still works great was an eyesore & I didn't match my other appliances. Dorothy L. • Raleigh , NC • March 24, 2014
I purchased a can of black appliance spray paint, removed the panels on the dishwasher, sprayed them, and a few hours later put them back. They're beautiful and it looks like I have a brand new dishwasher! It now matches everything and looks great with the new granite counter tops I just installed. THANK YOU FOR THE GREAT IDEA!!! I'm a 76 year old female and my friends think I'm a genius!
Read more
More
$42.95
- Compare At:
-
$51.11
- You Save:
-
$8.16
Genuine Whirlpool part
By: Whirlpool
Part Number: WP304231
Size: 8-18 x 1/2 inch.
Do-It-Yourself Stories from Customers like You
My whirlpool gas dryer wouldn't start was stuck in the "sensing" stage Kirill D. • Livingston , NJ • January 05, 2015
After I disassembled the dryer, I discovered that the belt was broken. Using a very handy video from the site I raced the belt and everything is back to normal
Read more
More
$5.95
- Compare At:
-
$7.08
- You Save:
-
$1.13