Kenmore Compactor 665.7342903 (6657342903, 665 7342903) Parts

Holds compactor bags securely during operation. Replace if cracked, broken, or handles are damaged. Installs inside compactor drum for easy bag removal.

Replacement drive hub that secures the compactor's power screw to the transmission. Needed when the original hub is worn, cracked, or broken.

This latch assembly secures the trash compactor drawer in the closed position and engages the safety interlock that allows the compactor to operate. It mounts to the front of the compactor frame and connects to the door switch mechanism. Replace this part if the drawer will not latch shut, the compactor fails to start because it does not detect a closed door, or the latch mechanism is visibly broken or worn.

This precision thrust race serves as the hardened bearing surface for axial loads in a rotating mechanism. Replacing a worn race reduces friction and noise, helping restore smooth, consistent motion and protect companion thrust bearings and washers from accelerated wear.

• Provides the hardened bearing surface for a thrust bearing assembly
• Supports axial load and helps maintain proper end-play in the mechanism
• Reduces friction to allow smoother rotation under load
• Wear may present as grinding/scraping noises, rough or binding motion, excessive axial play, or visible scoring

• Disconnect power and shut off water/gas before servicing
• Access the thrust-bearing area; note the order and orientation of races, bearings, and washers for reassembly
• Clean mating surfaces; replace any worn companion parts and lubricate only if specified by the service documentation
• Seat the new race fully and verify free movement by hand before reassembly and testing

Metal mounting bracket that secures internal components in your trash compactor. Replace if bent, damaged, or missing to restore stable part alignment.

Left side frame slide for trash compactors. Replaces cracked, broken, or worn slides that support the compactor drawer. Essential structural component.

Door strike plate for trash compactors. Mounts to cabinet frame to secure the door latch. Replace if cracked, bent, or missing to restore proper closure.

Fix excessive noise or wobbling components in your trash compactor with this wave washer retainer. Secures shaft-mounted parts to prevent movement.

Replacement power screw nut for trash compactors. Mounts on the drive screw mechanism. Order a new nut if yours is stripped, cracked, or worn out.

Latch spring for trash compactors. Installs in the door latch mechanism to provide tension. Replace if cracked, broken, or missing to restore proper latch function.

This bearing plate supports the dryer drum shaft and secures the bearing assembly so the drum spins smoothly and stays aligned. Replacing a worn plate restores stable drum rotation and helps reduce noise and rubbing. What it does:

• Provides a mounting surface and alignment for the drum bearing and shaft
• Keeps the drum centered to prevent wobbling, scraping, and uneven wear
• Reduces loud bearing or metal-on-metal noises caused by a damaged plate
• Helps maintain smooth drum rotation and proper belt alignment

• Turn power and gas off to the appliance before starting work
• Inspect surrounding components (bearing, shaft, seals, mounting screws) and replace if damaged
• Use correct fasteners and torque to secure the plate; improper mounting can cause noise or premature wear

Compactor door won't latch or latch feels loose? This E-ring retaining clip secures latch components to the shaft. Quick 5-minute fix for latch problems.

This latch pin secures the door latch mechanism on your trash compactor. Replace if the pin is broken, worn, or missing to restore proper door latching.

This power cord plate covers and secures the oven/range power cord where it enters the appliance, keeping the connection protected and helping prevent strain on the cord. It restores a finished look and helps keep wiring safely routed. What it does:

• Covers the terminal block area to protect power connections from dirt and accidental contact
• Helps keep the power cord routed and secured to reduce strain on the cord and terminals
• Can prevent air/dust intrusion behind the control cavity that could affect components
• Common replacement when the original plate is cracked, broken, or missing

• Always disconnect power at the breaker or unplug the appliance before starting work
• Typically attaches with two screws; keep screws and any gaskets from the old piece for reuse if undamaged
• Check the cord strain relief/terminal connections while replacing the plate; do not touch live terminals
• If wiring or the cord itself is damaged, replace or repair those parts per manufacturer instructions