Kenmore Microwave 721.85063010 (72185063010, 721 85063010) Parts

This turntable coupler connects the microwave's turntable motor to the glass tray, rotating it for even, consistent heating. Replace a worn or cracked hub to restore smooth tray motion and reduce noise during cooking.

• Couples the turntable motor to the glass tray for even heating
• Replaces a worn, cracked, or stripped hub that prevents rotation
• Helps reduce tray wobble and scraping sounds from the center
• Common symptoms: tray not turning, intermittent rotation, clicking/grinding at the hub

• Disconnect power before servicing; microwaves contain high-voltage components
• Remove the glass tray and roller ring; lift the old coupler straight up from the motor shaft (some models may require access from below per instructions)
• Align the new coupler with the keyed motor shaft and press it fully into place
• Reinstall the roller ring and tray; verify smooth, centered rotation

This customized nut is a small fastener used to secure components inside an appliance. Replacing a stripped, rusted, or missing nut restores a tight hold, reduces vibration, and helps keep panels and brackets properly aligned.

• Threads onto a matching screw or bolt to clamp parts together
• Maintains alignment of panels, brackets, and internal assemblies
• Helps prevent vibration, looseness, and rattling during operation
• Common failure signs: missing hardware, stripped threads, or components that won't stay tight

• Disconnect power; turn off water or gas before servicing
• Match the thread size/pitch to the original fastener before installation
• Hand-start threads to avoid cross-threading; tighten until snug—do not overtighten
• Replace any worn companion hardware (screw/bolt/washer) as needed

This door latch assembly for a microwave engages the door hooks and actuates the interlock switches so the unit recognizes a closed door, restoring proper latching and helping ensure the oven only operates when securely shut.

• Engages the door hooks to trigger the interlock switches and signal "door closed"
• Can help resolve no-start or "Door/Open-Close" indications with the door shut
• Addresses a door that won't latch, feels loose, or shows cracked/worn latch parts
• Built to mount in the original location and interface with existing door switches

• Disconnect power before service; microwaves contain high-voltage components that can retain a dangerous charge
• Access typically requires removing the control panel to reach the latch/interlock bracket
• Note switch orientation and spring positions; transfer any reusable hardware from the old assembly
• After installation, verify firm door engagement and proper interlock switch actuation before restoring power

This replacement screw secures specified panels or components inside your appliance. Refreshing worn or missing hardware helps restore a tight fit, reduce rattling, and keep assemblies properly aligned for reliable performance.

• Provides secure fastening for brackets, panels, or internal assemblies
• Replaces stripped, rusted, or lost hardware
• Helps reduce vibration and rattling noises
• Symptoms include loose panels, shifting components, or a screw that won't tighten

• Disconnect power and allow any hot surfaces to cool before servicing
• Wear cut-resistant gloves and eye protection
• Match length and thread to the original; replace like-for-like
• Start threads by hand to avoid cross-threading; do not overtighten

This truss head tapping screw secures panels, brackets, and covers in your appliance. Replacing a missing or damaged fastener restores a snug fit, reduces vibration, and helps keep components properly aligned for reliable performance.

• Provides low-profile holding power; wide truss head helps secure thin panels and trim
• Replaces lost, stripped, or corroded screws at the original mounting points
• Helps eliminate rattling, vibration, or loose handles/covers
• Addresses situations where a screw will not tighten or backs out during use

• Disconnect power; shut off water/gas if applicable before servicing
• Align parts and hand-start threads to avoid cross-threading
• Tighten until snug; do not overtighten to prevent stripping
• If the receiving hole is damaged, for repair before installing the new screw

Replacement refrigerator shelf that restores usable storage space and support for food and containers. Helps keep items organized, prevents spills, and returns a stable surface after a cracked, chipped, or missing shelf. What it does:

• Provides a flat, supportive surface for storing food, containers and small appliances
• Replaces cracked, chipped or missing shelving to restore usable interior space
• Helps reduce spills and keeps items from shifting when the door is opened or closed
• Seats into the refrigerator's existing shelf supports to re-establish stable storage

• Remove the old shelf per your owner's manual by lifting or sliding it out of the shelf supports
• Handle carefully; wear cut-resistant gloves if replacing a cracked or broken glass shelf
• Place the replacement shelf into the same supports—do not force or bend the shelf

This temperature-sensing safety switch monitors heat inside the microwave and opens or closes its circuit at a set point. Replacing a failed thermostat helps protect the unit from overheating and restores proper fan or heating control. What it does:

• Monitors surface temperature where it is mounted (cavity, duct, or component)
• Opens/closes its electrical circuit at a specific threshold to prevent overheating
• Can interrupt power to heating components or signal the exhaust fan, depending on design
• Symptoms can include: unit shuts off until it cools, runs but won't heat, exhaust fan won't auto-cycle or runs constantly

• Unplug the microwave; if over-the-range, remove it safely from the cabinet
• Discharge the high-voltage capacitor before servicing
• Note wire positions and transfer one lead at a time; ensure tight connections
• Mount firmly and flush to the original location/bracket for proper thermal contact

This Nut Assembly is a threaded fastener used to securely hold an associated component inside the microwave. Replacing a worn, stripped, or missing nut helps reduce vibration, eliminates rattling, and keeps parts properly aligned during operation.

• Provides a secure threaded anchor point for the matching screw/bolt
• Helps maintain alignment and prevent vibration or rattling
• Replaces stripped, cracked, or missing hardware
• Addresses symptoms like loose or shifting components and recurring rattling noises

• Disconnect power; if built-in, switch off the circuit breaker
• Access the mounting location, remove damaged hardware, and install the new nut assembly
• Avoid overtightening to prevent damage to threads or surrounding material

This replacement mounting screw secures panels and small appliance components to restore proper fit and prevent vibration or loose parts. A simple, direct replacement when the original fastener is missing or damaged. What it does:

• Secures panels, brackets, or small assemblies to keep parts aligned
• Stops rattling or vibration caused by loose or missing screws
• Restores normal fit where a stripped or corroded screw failed
• Matches the OEM fastener form for a correct, long-lasting fit

• Unplug the appliance or disconnect power before servicing
• Use the correct driver to avoid stripping the head
• Thread carefully and do not overtighten to prevent damage to threads or housing

This cooling fan motor spins the internal fan that moves air through the appliance to dissipate heat and protect sensitive components. Replacing a noisy, weak, or seized motor restores proper airflow and dependable operation.

• Drives the cooling fan to circulate cooling air within the cabinet
• Helps prevent overheating and thermal shutdowns of internal parts
• Restores airflow when the original motor is worn, noisy, or not turning
• Typical signs include no fan movement, unusual humming/squealing, reduced airflow, or the unit shutting off from heat

• Disconnect power (and gas, if applicable) before servicing; allow the appliance to cool completely
• Access the motor by removing the appropriate rear/top or control-panel cover for your model
• Note wire orientation; transfer the fan blade and any mounting parts from the original motor if required
• After installation, ensure the fan spins freely and verify proper airflow and quiet operation

The Cooling Fan Blade is an OEM part for LG microwaves. It circulates airflow around internal components to reduce temperatures during cooking.  

As it operates continuously, the tightly wound coils of the fan motor are prone to degradation and wear over several years of use. Damage to the fan housing can also inhibit proper functioning.

Causes of a bad cooling fan blade include:

• Broken or cracked plastic that unbalances the unit
• Worn down edges that decrease efficiency 
• Accumulated dirt that impedes ventilation

Symptoms of a bad cooling fan blade include:

• Overheating trips from the thermal cut-off  
• Cook times lengthening due to inefficient cooling
• Rattling or vibration noises emanating during operation

This OEM LG replacement ensures balanced airflow and consistent cooling for years of use. It is also compatible with some Kenmore and Sears/Kenmore microwaves.

This synchronous circulation motor powers the appliance's circulation function to move air or liquids reliably, restoring proper flow and operation. Designed to match OEM fit and performance for compatible LG units. What it does:

• Drives the appliance's circulation system to maintain proper airflow or fluid movement
• Helps resolve symptoms like weak or no circulation, reduced performance, or unusual motor noise
• Operates at consistent speed for steady system performance common to synchronous motors

• For safety, disconnect power before accessing the appliance and working near electrical components
• Install using OEM mounting points and connectors; verify alignment before securing
• Handle the motor carefully to avoid damage to the shaft and wiring

This is a replacement screw used to secure appliance components and panels. It restores proper fastening where a stripped, missing, or damaged screw causes loose parts or rattling. What it does:

• Fastens panels, trim, or internal components to maintain structural fit
• Helps stop vibration-related noise from loose assemblies
• Replaces missing or corroded screws that prevent proper closures
• Restores secure mounting after repairs or disassembly

• Use the correct screwdriver or bit to avoid stripping the head
• Tighten until snug—do not over-torque to prevent thread damage
• Keep small parts away from children and pets
• Disconnect power or water before accessing internal parts