Kenmore Microwave 721.85063010 (72185063010, 721 85063010) Parts

This bottom plate is the interior panel that covers and protects the oven or microwave floor, giving a clean cooking surface and shielding internal components from spills and debris. It helps maintain safe, reliable operation. What it does:

• Covers the appliance interior floor to catch drips and crumbs and keep them away from heating and mechanical parts
• Protects underlying components from corrosion and food damage
• Helps maintain even heat distribution by providing a stable cooking surface
• Worn, bent or missing plates can cause excessive debris buildup, odors, or contact with moving parts

• Disconnect power (unplug or switch off breaker) and allow the appliance to cool before starting
• Handle carefully—edges may be sharp; wear gloves if needed
• Install with existing factory screws or clips; do not force or bend the plate
• If other parts are damaged or missing, replace them per the manufacturer's instructions

Inner plastic door film covers the holes in the inner door frame.

This is the turntable assembly for the microwave's rotating tray system. It provides a stable, smooth-rotating surface so dishes stay level and heat evenly, replacing a damaged, wobbly, or missing turntable to restore consistent cooking performance. What it does:

• Forms the rotating surface that supports dishes for uniform heating
• Keeps the tray centered and aligned with the drive hub/guide for smooth motion
• Replace if the tray is cracked, chipped, or missing
• Replace if the tray rocks, binds, or skips while turning
• Helps address uneven heating caused by poor or inconsistent rotation

• 1 turntable assembly

• Unplug the microwave or switch off power at the breaker before servicing
• Remove the existing turntable parts and clean the track/hub area
• Set the new assembly so it sits flat and engages the drive hub; verify smooth, unobstructed rotation
• Do not operate the microwave without the turntable properly installed

This thermostat is a temperature-sensitive safety switch used in LG microwaves. It monitors internal temperature and opens the circuit when overheating is detected to help protect components from heat damage.

• Monitors temperature at its mounting location inside the microwave
• Opens on overtemperature to interrupt power for safety
• Depending on model/location, a failed or open thermostat can cause no heat, the unit shutting off mid-cycle, or no power until it cools
• Helps prevent damage to the magnetron, cavity, and wiring due to overheating

• Unplug the microwave before service; the high-voltage capacitor can retain a dangerous charge
• Note wire positions, remove mounting screws, and install the new thermostat flat against the surface for proper heat sensing
• Reassemble and test; ensure vents and filters are clear to maintain proper airflow and prevent future overheating

This is a motor start/run capacitor that helps the appliance's motor start and run smoothly by supplying a brief boost of electrical energy. Replacing a failing capacitor restores reliable motor startup and operation. What it does:

• Provides the brief electrical surge needed to start and keep the motor running
• Commonly linked to motors that hum, fail to start, or run intermittently
• Helps prevent overheating from repeated start attempts when functioning properly
• Works with the appliance's start circuitry to ensure consistent performance

• Disconnect power to the appliance before accessing electrical components
• Discharge the capacitor and use insulated tools
• Observe polarity/terminal layout and secure connections to factory specifications
• Dispose of the old capacitor according to local electronic-waste regulations

A Tap-Tite binding-head screw used to fasten appliance panels and components where a self-tapping metal thread is required. Replaces missing or damaged fasteners to restore secure assembly and reduce vibration or rattling. What it does:

• Creates its own mating thread in thin sheet metal for a secure hold without a nut.
• Holds panels, brackets, and trim in place to prevent looseness or movement.
• Commonly used where stripped, missing, or broken screws cause rattling, misalignment, or parts that won't stay attached.
• Compatible with standard screwdrivers or nut drivers sized to the binding-head.

• Disconnect power and unplug the appliance before working on it.
• Use the correct driver bit to avoid cam-out or head damage.
• Start straight and apply steady pressure; avoid overtightening to prevent stripping the formed threads.
• If the original hole is badly damaged, assess for repair or use of a larger fastener as needed.

This fan assembly replaces the oven/range cooling blower to restore proper airflow and help prevent overheating of control electronics. It's a direct-fit assembly designed to replace a failed or noisy blower unit. What it does:

• Circulates air to cool control components and maintain safe operating temperatures
• Replaces worn or failed blower motor that won't start or runs intermittently
• Restores airflow when the appliance is running hot or control board overheats
• Reduces rattling or grinding noise caused by a damaged fan or housing

• Turn off power to the appliance at the breaker before starting any repairs
• Inspect mounting points and wiring harness for damage; replace connectors if frayed
• Follow OEM service manual for removal and reinstallation torque and routing

This tapping screw secures appliance panels and components where a self-tapping fastener is required, restoring proper fit and reducing rattles or loose parts. Designed for exact-fit replacement when the original screw is missing or damaged. What it does

• Creates its own mating threads to fasten panels, brackets, or trim without a nut
• Restores secure attachment of loose or vibrating parts
• Helps eliminate squeaks, rattles, and misalignment caused by missing or stripped screws
• Matches OEM fit and form when replacing the original fastener

• Disconnect power and empty the appliance area before starting work
• Use the correct-size screwdriver or driver bit to avoid cam-out or head damage
• Start screws straight and avoid overtightening to prevent stripping the mounting hole
• Wear eye protection and follow the appliance manufacturer's service instructions