Kenmore Range 790.46764903 (79046764903, 790 46764903) Parts

This machine screw adjusts and secures the leveling leg or bracket, helping you set the appliance stable and plumb. Replacing a stripped, bent, or missing screw restores a solid footing and makes accurate leveling possible.

• Threads into the base or leveling bracket to raise or lower the appliance for proper leveling
• Helps reduce rocking, wobbling, and vibration from an unlevel installation
• Common signs of wear: stripped threads, bent hardware, corrosion, or a missing screw
• Useful during installation or when the existing adjustment screw no longer holds

• Disconnect power; shut off gas before working
• Support the appliance to relieve weight on the leveling point
• Remove the damaged screw; inspect and clean mating threads
• Start the new screw by hand to avoid cross-threading, then adjust height and snug

This motor drives the oven's convection fan to circulate hot air throughout the cavity for more even baking and roasting. Replacing a weak or noisy motor restores proper airflow and consistent cooking performance. What it does:

• Rotates the convection fan to move hot air uniformly across racks
• Helps maintain steady cavity temperatures during convection cycles
• Can resolve symptoms like a non-spinning fan, intermittent operation, or buzzing/grinding noises
• Improve uneven baking, poor browning, or extended cook times when convection is selected

• One motor

• Disconnect power at the breaker and allow the oven to cool completely
• Access the motor from the rear or through the oven cavity per your model's service procedure
• Note wire positions; transfer the fan blade and any mounting hardware from the old motor if required
• Ensure the fan spins freely by hand, secure wiring, then restore power and test convection operation

These chrome drip bowls sit beneath coil surface elements to catch spills and reflect heat. Sized for 8-inch and 6-inch burners, they refresh the cooktop's appearance and help elements seat correctly. What it does:

• Collects drips and splatters under coil elements and reflects heat back toward cookware
• Restores a clean look when originals are stained, pitted, or rusted
• Helps burners sit level and make solid contact with the cooktop
• Common signs to replace: heavy discoloration, rust, broken tabs, warping, lingering smoke or odor from burnt-on spills

• Two chrome drip bowls: one 8-inch and one 6-inch

• Disconnect power at the breaker and allow surface units to cool completely
• Pull the coil element straight out of its receptacle, then lift out the old bowl
• Align the new bowl's notches with the cooktop opening and seat it flat
• Reinsert the element fully and ensure it rests evenly in the bowl

This replacement drawer body restores a smooth-sliding storage bin in your appliance. Integrated rollers let the drawer glide on its tracks, keeping items organized and easy to access when the original is cracked, warped, or difficult to open.

• Forms the storage bin and supports items within the compartment
• Built-in rollers enable smooth travel along the drawer rails/tracks
• Helps resolve sticking, popping off track, rough movement, or broken tabs
• Restores proper fit and slide action for everyday use

• Empty and remove the damaged drawer; transfer any reusable front trim or inserts from the old drawer if needed
• Clean and inspect the rails/tracks; align the rollers with the track openings and slide in level until fully seated
• Do not force the drawer—re-align if resistance is felt to avoid damaging tabs or rails
• Avoid lubricants; wipe tracks and rollers with mild soap and water only

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

This heat-resistant insulation helps contain oven heat and shield surrounding components. Replacing worn insulation supports faster, more consistent preheating, steadier baking temperatures, and cooler exterior panels for safer, more efficient operation. What it does:

• Wraps/lines the oven cavity or panels to reduce heat loss and protect nearby wiring and controls
• Helps the oven preheat efficiently and maintain consistent cooking temperatures
• Limits heat transfer to exterior panels and surrounding cabinetry
• Common signs of failure: longer preheat times, temperature swings, unusually hot sides/back, or insulation that is burnt, brittle, soaked, or missing

• 1 insulation piece

• Disconnect power and, if applicable, shut off gas before servicing
• Access typically requires removing rear/side panels or sliding the unit out; take photos to aid reassembly
• Wear gloves and a dust mask; handle gently—do not compress insulation and keep clear of sensors/wiring
• Re-secure with original clips/tape, reinstall panels, then test preheat and check for abnormal exterior heat

This spacer sets the correct gap between mating parts in your appliance's assembly, preventing rubbing and misalignment. Replace a missing or worn spacer to restore a solid fit, reduce noise, and protect surrounding components.

• Maintains proper spacing between components for correct alignment and operation
• Reduces metal-to-metal contact, squeaks, and premature wear
• Helps fasteners and panels seat securely
• Typical symptoms when failed: loose or rattling parts, uneven gaps, or visible wear marks

• Disconnect power; for gas models, shut off the gas. Allow the appliance to cool completely.
• Access the assembly per your model's diagram; note the original orientation/stack-up before removal.
• Reuse original fasteners if serviceable; hand-start threads and tighten snugly to avoid damaging the spacer.
• Verify alignment and clearances before fully reassembling. Quantity and location vary by model.

This high-temperature insulation is used in the oven assembly to contain heat and protect nearby components and cabinetry. Replacing damaged insulation helps the appliance maintain set temperatures and keeps exterior surfaces from getting excessively hot. What it does:

• Helps retain heat for stable baking and roasting temperatures
• Reduces heat transfer to the appliance frame and adjacent cabinets
• Replaces insulation that is torn, charred, or saturated with spills/grease

• One insulation piece

• Disconnect power; for gas models, also shut off the gas supply
• Remove the range or wall oven and access the oven body
• Wear gloves, eye protection, long sleeves, and a dust mask; fibers can irritate skin and lungs
• Reinstall in the same orientation/routing as the original; do not compress insulation or block vents

This appliance screw fastens panels, brackets, and other components inside the unit. Replace a missing, rusty, or stripped fastener to restore a secure fit and help prevent rattles, misalignment, or premature wear.

• Secures appliance components such as panels, brackets, and covers
• Restores proper fit when an original screw is missing or stripped
• Helps reduce vibration and noise from loose parts
• Common signs: loose or misaligned parts, rattling, or a missing screw

• Disconnect power before servicing
• Match the new screw to the original for size and thread before installing
• Hand-start threads to avoid cross-threading; do not overtighten
• Reuse any original washers or clips if they were used with the old screw

A decorative medallion trim piece that restores the finished look of your appliance front. Replaces a scratched, faded or missing medallion to improve appearance and maintain original styling. What it does:

• Covers and protects the underlying surface while matching the appliance's original finish
• Restores a clean, finished look when the factory medallion is damaged or discolored
• Helps keep grime and moisture out of seams around the emblem area
• Useful when replacing a damaged control/door trim for a consistent appearance

• One medallion decorative trim

• Surface-mount replacement; peel adhesive or fasten per original attachment method
• Clean and dry mounting area before installing for best adhesion
• Handle carefully to avoid scratching the finish during installation

This is a #8 screw, 0.500 inch long, used to secure panels and components in appliances. It provides a correct-fit fastener for repairs where the original #8 x 1/2" screw was required, restoring proper assembly and stability. What it does:

• Fastens trim, panels, brackets and small components where a #8 x 1/2" screw is specified
• Holds parts securely to prevent rattling, gaps or loose panels
• Replaces worn, stripped or missing screws to restore proper fit
• Appropriate for common interior and exterior appliance mounting points

• Use the correct screwdriver (typically Phillips) and avoid over-tightening to prevent strip or damage
• Disconnect power and follow appliance manufacturer safety instructions when accessing internal parts

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This mounting bracket secures internal components to the appliance cabinet, restoring proper alignment and stable support where factory brackets have broken or come loose. A direct-fit replacement that helps stop shifting, rattles, and misalignment. What it does:

• Provides a secure mounting point for panels, assemblies, or components inside the cabinet
• Restores correct alignment when a damaged bracket allows parts to sag or move
• Reduces vibration and rattling caused by loose or missing support
• Helps maintain proper clearances for doors and internal assemblies

• One replacement mounting bracket

• Disconnect power to the appliance before starting any repair
• Remove any obstructing panels, shelves, or components to access the bracket
• Keep original fasteners; replace only if explicitly specified by OEM instructions