Kenmore Range 790.46782900 (79046782900, 790 46782900) Parts

This decorative trim piece restores the finished appearance on the appliance door or control area and covers the mounting edges for a clean, factory look. Replaces a scratched, dented, or missing trim to improve appearance. What it does:

• Covers and protects the edge of the door or control opening to keep a finished appearance
• Hides fasteners and gaps for a smoother exterior surface
• Prevents dirt and moisture from collecting in the trim gap
• Restores original aesthetics after damage or during panel replacement

• One decorative trim piece

• Install with basic hand tools; align trim over mounting area before fastening
• Do not force or bend trim; inspect adjacent mounting tabs for damage
• Disconnect power to the appliance if installation requires removing electrical panels or access behind the trim
• Replace with OEM-specified fasteners for a secure fit

This genuine OEM door outer panel manufactured by Frigidaire is intended to replace a broken or faulty part in ovens. The door outer panel allows the user to easily access the interior of the oven whilst still keeping the heat properly sealed inside the appliance. If the door outer panel becomes worn or deteriorated, including being cracked, dented, bent, or detached, it may prevent the appliance from being used as intended or heating up properly. Make sure that the appliance is completely powered off and unplugged from the outlet before undergoing any repairs. Wear work gloves to prevent injuries.This is door outer panel has been sourced from the manufacturer and is compatible with ovens manufactured by Frigidaire, Electrolux, Gibson, Westinghouse, Kelvinator, and other brands. This part has been made from high-quality, durable, non-corrosive metal, glass, and other materials and is only sold individually.

This handle mounting screw is an authentic OEM replacement part sourced directly from the manufacturer for use with oven handles. The oven handle attaches to the oven door with two of these screws. If the washer that goes with the screw is loose or missing, the screw will become loose, and the handle may break away from the door. If this occurs, the door will be difficult to open when not in use and nearly impossible to open when hot. If the mounting screw is loose or missing, the screw should be replaced immediately. Note that the washer needed for the screw is not included and should be purchased separately.Make sure the oven is not hot before replacing the door handle mounting screw. To start, disconnect the power from the oven. Remove the screw and washer from the handle if it is loose and install a new handle mounting screw with a new washer. Tighten the screw until it is flush with the door. Repeat for the remaining screw if necessary.This handle mounting screw is a heavy-duty black metal screw that is sold individually. It is designed for use on ovens manufactured by Frigidaire.

A direct-fit round control knob that restores tactile control of your appliance's settings. Replaces a worn, cracked, or missing knob so you can reliably select heat and function positions. What it does:

• Provides a secure grip to turn the appliance control shaft for temperature or function selection
• Replaces broken, loose, or stripped knobs that prevent accurate setting changes
• Helps restore precise pointer alignment so marked settings match actual selection
• Fits standard shaft-style controls used on many Frigidaire ranges and ovens

• Disconnect power to the appliance before replacing control knobs to avoid injury
• Pull the old knob straight off the control shaft; align and push the new knob onto the shaft until fully seated
• Do not force the knob—if it does not slide on easily, verify shaft type and orientation
• If the control shaft is damaged or the knob still slips after installation, replace the underlying control.

This door push-button light switch controls the interior lamp by turning it on when the refrigerator door opens and off when the door closes. It replaces a worn or failed push-button actuator to restore reliable light operation. What it does:

• Completes the circuit to the interior light when the door opens and breaks the circuit when closed
• Commonly causes no interior light, intermittent lighting, or lights that stay on
• Fits in the refrigerator door frame and interfaces with the existing wiring harness
• Simple, single-function electromechanical switch—no electronics to program

• One door push-button light switch

• Disconnect power to the appliance before servicing to avoid shock
• Remove the door trim or bezel as needed to access the switch (requires basic hand tools)
• Handle the switch and wiring gently; do not force connectors or overtighten fasteners

This element hanger support secures a cooktop surface heating element to the range and keeps the element aligned for reliable contact and stable cooking. Replaces a worn or bent bracket to restore proper element positioning. What it does:

• Holds the surface heating element in the correct position under the cooktop
• Stabilizes the element to maintain solid electrical contact and even heating
• Helps prevent element wobble, arcing, or intermittent power to the burner
• Fits where the element connects to the terminal/anchor point on the cooktop

• 1 element hanger support bracket

• Disconnect power to the appliance before attempting any service
• Remove the cooktop or element as required to access the hanger; follow OEM disassembly steps
• Inspect element terminals and surrounding parts for damage while replacing the bracket

This shoulder screw secures moving or fixed appliance components by providing a built-in spacer and pivot point for proper alignment and smooth operation. It restores correct fit where a worn or missing shoulder fastener causes play. What it does:

• Provides a precision spacer and pivot for hinges, drawers, or linkage assemblies
• Holds components at the correct distance to prevent rubbing and binding
• Helps stop wobble, misalignment, rattling, or uneven movement when the original shoulder screw is worn or missing
• Works where a headed screw with an integrated shoulder is required for smooth rotation or exact spacing

• One shoulder screw

• Disconnect power and remove the appliance panel or access covers before replacing hardware
• Handle small parts carefully to avoid dropping them into assemblies; magnetic pickup tool can help
• Install in the original location and tighten securely but avoid overtightening; do not modify the shoulder or thread
• If the screw secures a load-bearing hinge or mechanism, verify alignment and operation after installation