Kenmore Range 790.72502010 (79072502010, 790 72502010) Parts

This oven door latch assembly locks the door during self-clean and reports lock status to the control. Restores proper door locking and unlocking so bake and clean cycles can run safely and without interruptions. What it does:

• Secures the oven door during self-clean and when commanded by the control
• Provides locked/unlocked position feedback to the electronic control
• Helps resolve issues such as a door that won't lock or unlock
• Can address self-clean cycles that won't start or complete and lock-related error messages

• 1 latch assembly

• Disconnect power at the breaker and allow the oven to cool completely
• Access varies by model; you may need to pull the unit and remove the rear or top/control panel
• Photograph wire connections and linkage before removal; transfer any mounting hardware from the original
• After installation, test the lock operation before final reassembly

This door trim kit restores the finished edge around the appliance door, covering raw edges and fasteners. Replace worn or missing trim to refresh the look and help keep the outer door panel properly seated. What it does:

• Finishes the perimeter of the door and conceals mounting hardware
• Helps retain and align the outer door panel or glass
• Replaces cracked, warped, loose, or missing trim pieces
• Typical symptoms include gaps around the door, loose or rattling edges, or cosmetic damage

• One door trim kit

• Disconnect power to the appliance before servicing
• Wear cut-resistant gloves; door edges and trim can be sharp
• Support or remove the door as required by your model; note screw locations and lengths
• Transfer any clips/screws from the original trim and check door alignment and operation after installation

This oven light lens retainer secures the glass light cover to the oven cavity so the bulb area stays protected during cooking. Replacing a damaged or missing retainer keeps the lens firmly in place and prevents nuisance loosening.

• Holds the glass light lens securely inside the oven cavity
• Helps shield the bulb area from splatters and debris
• Direct replacement for a bent, warped, or missing retainer ring
• Common symptoms: lens won't stay in, cover rattles, or difficulty securing the lens after service

• Disconnect power at the breaker and allow the oven to cool completely
• Remove oven racks for easier access to the light cover area
• Support the glass lens while positioning the retainer to avoid drops or chipping
• Secure the retainer per your model's design; do not overtighten

This surface burner grate supports cookware on your gas cooktop, keeping pots and pans stable above the flame. Replace a cracked or warped grate to restore safe pan support and consistent burner performance.

• Holds cookware at the proper height above the burner flame
• Provides a stable, level surface for pots and pans
• Replace if cracked, warped, or missing to prevent wobbling or tipping
• Common symptoms include unstable cookware, uneven heating, or visible damage to the grate

• Turn all burners off and allow the cooktop to cool completely before handling
• Lift off the old grate and clean the area if needed
• Position the new grate so its feet sit flat and openings align with burner caps
• Test with a pan to confirm it sits level and stable

This door hinge is a direct-fit replacement part that supports and aligns an appliance door for smooth opening and secure closing. Replacing a worn hinge restores proper fit and prevents door sag, binding, or noisy operation. What it does:

• Provides the pivot point that lets the door open and close smoothly.
• Keeps the door aligned so seals meet and the door closes fully.
• Restores stable door movement and reduces sagging or rubbing.
• Helps stop binding, unusual noises, or doors that don't stay closed.

• Disconnect power to the appliance (and water supply if applicable) before starting work.
• Support the door while removing or installing the hinge to prevent damage or injury.
• Keep original screws and mounting hardware; new fasteners may be required if originals are worn.

This small replacement spacer positions and secures appliance components to maintain correct alignment and fit. Installing the spacer restores proper panel spacing and reduces vibration where a worn or missing spacer causes looseness or rubbing. What it does:

• Maintains the correct gap between panels, trim, or assemblies to ensure parts fit flush
• Keeps components aligned to prevent rubbing, binding, or uneven wear
• Helps reduce vibration and rattling caused by a missing or damaged spacer
• Preserves original part spacing for reliable operation of the surrounding components

• Disconnect power to the appliance before any service to avoid shock or injury
• Remove any trim or fasteners that block access; keep track of screws and small parts
• Match the new spacer's orientation to the original; do not force parts into place

Replacement screw that secures panels, trim and internal components in compatible appliances. Restores proper fit and helps reduce rattling or loose parts when the original fastener is missing, worn, or damaged. What it does:

• Fastens panels, brackets, trim pieces and small component assemblies to the appliance frame
• Helps eliminate noise and vibration caused by loose or missing fasteners
• Replaces stripped, corroded or missing screws to restore secure mounting
• Matches OEM fit when the identical screw is required for proper alignment

• Disconnect power to the appliance before starting any repair
• Use the correct driver size to avoid cam-out or damage to the screw head
• Do not overtighten; overtightening can strip threads or crack plastic parts

This insulation panel fits inside the refrigerator cabinet to help maintain consistent temperatures and reduce heat transfer. It preserves cooling efficiency and helps minimize frost and condensation when the appliance is operating properly. What it does:

• Provides thermal barrier between the cabinet and outer shell to help maintain internal temperature
• Helps reduce frost buildup and interior condensation when sealing and cooling systems are functioning
• Can improve energy efficiency by minimizing unwanted heat gain
• Dampens vibration and can reduce operating noise from the compressor area

• Disconnect power to the appliance before starting any repair to avoid electric shock
• Handle insulation carefully—avoid compressing or tearing the material to retain thermal performance
• Remove interior panels or shelving as needed to access the installation area; keep track of fasteners
• If the original insulation is damaged or contaminated, replace it and check nearby seals and gaskets for proper fit

This electrical receptacle is the small connector that secures a wiring plug to an appliance component, restoring a reliable electrical connection and preventing intermittent operation or arcing. What it does:

• Provides a secure plug-in connection between a wire harness and a component
• Restores power to a component when the original connector is cracked, melted, or corroded
• Helps prevent loose connections that can cause intermittent operation or sparks
• Fits the OEM-style wiring configuration for a direct replacement

• Disconnect power to the appliance before starting any repair
• Remove the damaged connector and match the replacement to the harness before installing
• Use basic hand tools; avoid forcing terminals to prevent damage

This door hinge cover shields and protects the refrigerator hinge area from dirt and damage while giving the hinge a finished appearance. Replaces a worn, cracked, or missing cover to restore proper fit and appearance. What it does

• Covers and protects the door hinge assembly from debris and accidental contact
• Helps maintain a finished look by hiding hinge hardware and mounting fasteners
• Prevents sharp edges from being exposed, reducing snag and scratch risk
• Commonly replaced when cracked, broken, or missing after impact or wear

• One door hinge shield

• Remove power and open the door before servicing to prevent injury
• Typically installs with a few screws or clips—retain original fasteners unless replacement specified
• Handle part carefully to avoid scratching painted surfaces; align shield before tightening

A small replacement retainer clip that secures trim, panels or components in place to restore proper alignment and stop rattles or loosening. Fits original mounting points for a factory-style repair. What it does:

• Secures refrigerator trim, panels or small components to prevent movement and noise
• Keeps parts aligned so doors and drawers fit and operate smoothly
• Helps maintain grille, kickplate or interior trim attachment where clips are used
• Simple, non-electrical part — no wiring or calibration required

• Basic hand tools usually required; access the clip location before removal
• Remove any panels gently to avoid damaging surrounding trim or fasteners
• Replace only the worn or broken clip; align part fully before snapping into place
• Disconnect power to appliances with electrical components before starting work

This factory screw secures components in your appliance, restoring a tight, rattle-free fit. Replace missing or damaged hardware to keep panels, brackets, and trim properly fastened and aligned for safe, reliable operation.

• Secures panels, brackets, trim, or internal components to the chassis
• Replaces lost, rusty, stripped, or cross-threaded screws
• Helps eliminate looseness, gaps, and vibration/rattling
• Common signs: loose/misaligned panels or trim, rattling noises, missing or rounded screw heads

• Disconnect power (and shut off gas if applicable); allow the unit to cool completely
• Match to the original location and replace one at a time to maintain alignment
• Hand-start to prevent cross-threading; tighten snugly—do not overtighten
• Use light torque when threading into plastic or thin sheet metal

A replacement protective shield that covers and protects internal appliance components from debris, moisture and incidental contact. Restores protection to damaged or missing shields to help maintain safe, reliable operation. What it does:

• Covers and protects wiring, connectors or nearby parts from accidental contact and debris
• Helps prevent moisture or food particles from reaching sensitive components
• Replace if the shield is cracked, warped, missing or allows exposed parts
• Reduce rattles or contact-related noises caused by loose or damaged shields

• Shield

• Disconnect power to the appliance before starting any repair
• Use care around sharp edges; wear gloves and eye protection
• Remove fasteners holding the old shield; reuse or replace screws as specified by the manufacturer