Kenmore Range 790.72902011 (79072902011, 790 72902011) Parts

Replacement screw secures panels, trim, and internal components in your appliance. Needed when original fastener is missing, stripped, or damaged.

Replace a cracked, broken, or missing oven door spacer that maintains proper alignment and gap between door components. Installs in door assembly.

Burner tube for gas ranges. Connects gas valve to burner assembly. Replace if cracked, corroded, or leaking to restore proper gas flow to cooktop burners.

This ignitor orifice assembly replaces the gas burner orifice and ignitor mounting used to safely direct gas to the oven burner so the igniter can light. Restores reliable ignition for gas ovens and ranges. What it does:

• Directs gas flow to the oven burner through the correct orifice size for proper ignition
• Positions and secures the ignitor so the spark/heat source can light the burner
• Helps resolve symptoms like a burner that won't ignite, delayed ignition, or weak burner flame
• Works as a service replacement for damaged, clogged, or corroded orifice/ignitor fittings

• One ignitor orifice assembly

• Turn off gas supply and power before starting any repair; follow appliance shutoff procedures
• Handle the ignitor carefully—it's fragile and can be damaged by rough handling or static
• Use appropriate wrenches and avoid overtightening the orifice fittings to prevent damage

This is the hinge receptacle that secures the oven door hinge to the range frame, allowing the door to pivot open and closed smoothly. It acts as the mounting socket where the hinge arm locks into place. Replace this part if the oven door is sagging, not closing evenly, or if the hinge feels loose or disconnected from the frame.

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist

Burner won't ignite or flame won't adjust? This top burner valve controls gas flow to your cooktop burner, restoring proper ignition and flame control.

Secures range trim, panels, and components to prevent rattles and loosening. Replace when clips break or lose tension. Confirm fit with your model number.

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

Replaces a worn, broken, or missing storage drawer glide for smooth sliding operation. Installs on the drawer track to restore proper alignment and movement.

This metal rack fits inside the warming drawer beneath the oven, providing a flat surface to hold plates, dishes, or cooked food at a warm serving temperature. It slides in and out of the drawer on built-in guides. Replace it if the rack is bent, warped, rusted, or missing, which can prevent proper food placement and even heat distribution in the warming drawer.

Replacement mounting screw for ovens and ranges. Secures panels, brackets, trim, and internal components. Replace missing or stripped screws to restore fit.

A replacement hex-head screw used to secure appliance regulator brackets and similar small components. Restores proper fastener fit so panels and brackets stay firmly attached. What it does

• Fastens regulator bracket and related sheet-metal components
• Provides a secure threaded connection for components where an 8-18 thread is specified
• Helps eliminate looseness or rattling caused by a missing or damaged screw
• Matches the nickel/chrome finish commonly used on interior mounting locations

• One hex head screw (8-18 x 3/8), nickel finish

• Intended for use where an 8-18 x 3/8 hex screw is specified by the manufacturer
• Tighten to snug; avoid over-torquing which can strip sheet-metal threads
• Turn off power to the appliance before accessing internal components
• If the original screw used a lock washer or threadlocker, replace or reapply as appropriate

This is a metal cover that fits over the convection fan assembly in the back wall of the oven cavity. It protects the fan and heating element while allowing hot air to circulate evenly during convection cooking. Replace this cover if it is warped, cracked, or corroded, which can cause uneven heating or rattling noises during convection baking.

Secures gas valve assemblies and mounting brackets to your range. Replace if screw is stripped, missing, or corroded to keep valve hardware stable.