Kenmore Range 790.9642240C (7909642240C, 790 9642240C) Parts

This support plate secures internal components and provides a stable mounting surface to reduce vibration and keep parts aligned. It restores proper fit and helps stop rubbing, rattling, or loose-panel symptoms. What it does

• Provides a flat, stable mounting surface for adjacent components
• Holds parts in correct position to prevent movement and noise
• Helps maintain proper clearances so panels and assemblies fit without rubbing
• Can be replaced if bent, cracked, or missing fasteners that cause vibration or loose parts

• Disconnect power before servicing to avoid shock or injury
• Verify plate orientation and fastener locations before removing old part
• Use existing screws if undamaged; replace damaged fasteners for secure fit
• Handle edges carefully; wear gloves to avoid cuts during install

This replacement glide restores smooth, supported movement for a refrigerator or freezer drawer. It prevents catching and uneven travel so drawers open and close reliably and stay properly aligned. What it does

• Replaces a worn or broken drawer glide to restore smooth sliding motion
• Supports the drawer to prevent sagging or misalignment during use
• Reduces rubbing, scraping, and noisy operation when opening or closing the drawer
• Helps prevent the drawer from sticking or coming off its track

• One glide

• High-level swap: remove the drawer to access the glide, unfasten the old piece, then secure the new glide in the same position
• Use appropriate hand tools; avoid forcing parts to prevent cabinet or track damage
• Wear gloves to protect hands and disconnect power if working near electrical components
• Replace fasteners before reinstalling the drawer

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit

This hex flange nut secures components where a broader bearing surface is needed to resist loosening and distribute load. It fits 10-32 threaded studs and is used on fastened assemblies in appliances. What it does:

• Provides a secure threaded connection for 10-32 screws and studs
• Flange spreads clamping force to reduce panel or bracket damage
• Hex shape allows tightening with a wrench for a reliable hold
• Commonly replaces worn or missing nuts that cause loose panels or rattling

• One hex flange nut

• Use the correct 10-32 screw or stud and hand-start threads to avoid cross-threading
• Tighten with an appropriately sized wrench; do not overtighten to prevent thread or part damage
• Disconnect power and follow appliance safety instructions before servicing
• Replace only like-for-like; confirm size and thread match your application

This glide is a replacement drawer slide that helps the refrigerator or freezer drawer open and close smoothly and stay aligned. It restores stable drawer movement and reduces sticking or uneven travel. What it does:

• Guides the drawer along its track for smooth, controlled opening and closing
• Keeps the drawer aligned to prevent rubbing, binding, or uneven movement
• Replaces worn or damaged glides that cause sticking, sagging, or noisy operation
• Works as a structural support point for the sliding drawer assembly

• One replacement glide

• Basic hand tools are typically all that's needed; remove the drawer to access the glide
• Compare the old glide to this part before installing to confirm fit and orientation
• Keep fingers clear of pinch points; wear gloves if needed and follow appliance power-off safety
• If fasteners are stripped or broken, replace them with OEM-equivalent hardware

The Lens is an OEM component for Frigidaire freezers. It acts as a transparent cover and protective barrier for the freezer compartment lights. Crafted for durability and clarity, the lens avoids frost and minimizes condensation while allowing visibility inside the freezer.

Causes of a bad lens can include deep scratches or cracks developing over time from repeated wiping or exposure to chemicals like frost removers.

Symptoms of a bad freezer lens include:

• Cloudiness, fogginess, or smears inhibiting internal visibility
• Cracks or breaks compromising the protective barrier
• Distorted views make it difficult to assess food levels
• Diffused lighting with shadows instead of a clear view

This OEM Frigidaire part can also be used on Electrolux, Frigidaire, Gibson, Kelvinator, Westinghouse, and Sears/Kenmore.

Restore smooth, level oven rack movement with this right-side rack support. It mounts to the oven wall to hold and align the racks at the correct heights so cookware stays stable while baking and roasting.

• Mounts on the right interior wall to support and guide oven racks
• Keeps racks level and properly spaced across multiple positions
• Replaces a bent, cracked, or missing side rail
• Typical symptoms: racks wobble, bind, tilt, or won't slide in/out smoothly

• Disconnect power and allow the oven to cool before servicing
• Remove oven racks to access the side support
• Retain and reuse existing mounting hardware unless directed otherwise by your model's service instructions
• The rail is seated and level before reinstalling the racks

This replacement shield is a molded protective mounting shield that helps protect internal appliance components from debris and physical damage, keeping parts aligned for reliable operation and quieter performance. What it does:

• Covers and protects wiring, harnesses, or small components from contact and debris
• Helps maintain proper alignment of nearby parts to reduce wear and noise
• Prevents incidental interference between moving parts
• Restores intended component protection after damage or removal

• One replacement shield

• Disconnect power before starting any repair to avoid shock or injury
• Handle plastic tabs and mounting points carefully to avoid breaking clips
• Reuse original fasteners if undamaged; replace any broken clips before powering appliance