Kenmore Range 790.96613402 (79096613402, 790 96613402) Parts

Secures the glass light cover to your range oven cavity. Replace if the retainer is cracked, broken, or missing to keep the lens firmly in place.

Black control knob for electric range selector, timer, or temperature shaft. Replace worn, missing, or broken knobs. Simple push-on fit with textured edge.

Broiler pan rack for electric ovens and ranges. Replaces cracked, warped, or missing racks. Installs inside broiler pan for elevated cooking.

Size: 6-20 x 0.312 inch.

A replacement motor latch that secures the motor assembly to the appliance chassis, helping keep the motor stable during operation for smoother performance and reduced vibration. Fits specific Frigidaire/WCI motor assemblies. What it does:

• Secures and positions the motor assembly to prevent excessive movement
• Helps reduce vibration and rattling caused by a loose motor mount
• Restores proper alignment between motor and drive components
• Can eliminate intermittent contact-related noise from a shifting motor

• Disconnect power (unplug or switch off breaker) before starting any repair
• Installation typically requires accessing the motor area—expect to remove panels or the cabinet
• Keep track of mounting hardware; replace any damaged fasteners
• Test operation after reassembly; stop and recheck if noises or vibration persist

Stop rattling and loose panels in your range with this support plate. Secures internal components, reduces vibration, and restores proper alignment.

Exterior trim panel that houses and protects your range's control interface and display. Replace if cracked, broken, or worn to restore a clean appearance.

Secures range trim, panels, and components to prevent rattles and loosening. Replace when clips break or lose tension. Confirm fit with your model number.

Mounting screw for securing range panels, brackets, and igniters. Replace if stripped, missing, or damaged to restore proper fastening and alignment.

Molded insulation liner that fits inside the range oven cavity. Replace if yours is damaged, compressed, or missing to restore proper heat containment.

This evaporator fan cover protects the refrigerator evaporator fan assembly and helps direct airflow for proper cooling. It's a molded replacement part that restores the original airflow path and prevents debris contact with the fan. What it does:

• Shields the evaporator fan and motor from ice buildup and loose debris
• Directs airflow across the evaporator for even cooling in the freezer compartment
• Helps reduce fan noise by stabilizing airflow around the fan housing
• Commonly replaced when cracked, broken mounting tabs are present, or airflow is obstructed

• One fan cover

• Disconnect power before accessing the evaporator compartment to avoid shock and fan injury
• Remove food and evaporator access panels per model service instructions before replacing the cover
• Handle clips and mounting tabs gently—use proper fasteners if any original hardware is damaged
• If you encounter ice buildup on the evaporator, fully defrost and address the underlying cause before reassembly

Replaces a worn, broken, or missing storage drawer glide for smooth sliding operation. Installs on the drawer track to restore proper alignment and movement.

Range indicator light lens kit with red and clear lenses. Replace when cracked, discolored, or missing. Fits control panel burner indicators. Verify fit.

Support plate that mounts to the bottom of your range oven cavity. Replace if the original plate is cracked, warped, or damaged from heat exposure.

This is a replacement mounting screw used to secure the dual safety valve assembly on compatible gas ranges and ovens. It restores proper fastening so the valve stays firmly in place during operation. What it does

• Secures the safety/dual gas valve to the appliance chassis or manifold
• Prevents valve movement that can interfere with burner operation or alignment
• Commonly replaced when original screw is missing, stripped, or damaged
• Matches OEM thread size and length for correct fit and retention

• One (1) screw, size 10-16 x 0.486

• Disconnect power and shut off gas supply before starting work; follow all safety procedures
• Thread carefully to avoid cross-threading; do not overtighten — snug to OEM torque specification
• Inspect surrounding mounting holes and hardware; replace any stripped or damaged parts for a secure fit